The FA goods manufactured by Mitsubishi Electric Engineering Co., Ltd. include various types of equivalent terminal block converter modules, e.g. screw terminal block type, spring clamp terminal block type and e-CON terminal block type. An appropriate one can be selected from the wide product line.
For details on the FA goods manufactured by Mitsubishi Electric Engineering Co., Ltd., please contact your local Mitsubishi sales office or representative.
•‥ Using‥the‥relay‥terminal‥modules,‥a‥large‥type‥A‥(Large‥Type)‥Series‥32-point‥contact‥output‥
module‥can‥be‥replaced‥while‥maintaining‥8‥points/common.
•‥ A‥wide‥variety‥of‥compatible‥wire‥sizes‥are‥available‥using‥the‥relay‥terminal‥module.
A‥(Large‥Type)‥Series‥32-point‥contact‥output‥module‥AY13:‥Max.‥2‥mm2 Relay‥terminal‥module:‥Max.‥1.25‥mm2
Q‥Series‥16-point‥contact‥output‥module‥QY10:‥Max.‥0.75‥mm2
•‥ Replacement‥is‥possible‥without‥the‥need‥of‥additional‥modules‥because‥a‥module‥mounted‥on‥
the‥base‥unit‥becomes‥compatible‥with‥32-point‥connector‥type‥modules‥through‥the‥use‥of‥the‥
"connector/terminal‥block‥converter‥module".‥
(a)‥System‥configuration‥example
Current‥configuration After‥replacement
Replace
For positive common input modules and sink output modules (standard type) For positive common input modules and sink output modules (2-wire type) For positive common input modules (3-wire type)
For negative common input modules (standard type) For negative common input modules (2-wire type) For negative common input modules (3-wire type) For source output modules (standard type) For source output modules (2-wire type)
0.4 kg 0.5 kg 0.6 kg 0.4 kg 0.5 kg 0.6 kg 0.4 kg 0.5 kg
2.1 Replace A/QnA (Large Type) Series with Q Series
The following is an example of replacing contact output modules (AY13) with transistor output modules (QY41P) and externally converting transistor outputs into contact outputs.
● Instructions
Replace AY13 with QY41P and connect the relay terminal modules to convert to contact outputs.
With this method, the system can be upgraded without increasing the number of modules on the base unit.
Also, 8 points/common, the same specification as that of the AY13, can be maintained.
Q61P Q01UCPU QX41 QX41 QX41 QX41 QX42
Q61P QY41P QY41P QY41P QY41P QY41P
A61P A2NCPU AX41 AX41 AX41 AX41 AX42
A61P AY13 AY13 AY13 AY13 AY13
X00... X20... X40... X60... X80...
YC0... YE0... Y100... Y120... Y140...
A35B
A65B
QY41P
16-point relay terminal module x 2 (A6TE2-16SRN) Dedicated cable
(ACTE)
Reray terminal module Reray terminal module 8 points/common
(the same specification as that of AY13)
•‥ Using‥the‥relay‥terminal‥modules,‥a‥large‥type‥A‥(Large‥Type)‥Series‥32-point‥contact‥output‥
module‥can‥be‥replaced‥while‥maintaining‥8‥points/common.
•‥ A‥wide‥variety‥of‥compatible‥wire‥sizes‥are‥available‥using‥the‥relay‥terminal‥module.
A‥(Large‥Type)‥Series‥32-point‥contact‥output‥module‥AY13:‥Max.‥2‥mm2 Relay‥terminal‥module:‥Max.‥1.25‥mm2
Q‥Series‥16-point‥contact‥output‥module‥QY10:‥Max.‥0.75‥mm2
•‥ Replacement‥is‥possible‥without‥the‥need‥of‥additional‥modules‥because‥a‥module‥mounted‥on‥
the‥base‥unit‥becomes‥compatible‥with‥32-point‥connector‥type‥modules‥through‥the‥use‥of‥the‥
"connector/terminal‥block‥converter‥module".‥
Solution and Benefit
(a)‥System‥configuration‥example
Current‥configuration After‥replacement
Replace
(2) Replace 32-point contact output type module using "relay terminal module"
Product name
Power supply module A61P 2 Q61P
Existing model Replacement model 2
CPU module A2NCPU 1 Q01UCPU 1
Main base unit A35B 1 Q38B* 1
Extension base unit A65B 1 Q68B 1
Extension cable AC06B 1 QC06B 1
Input module AX41 4 QX41-S2 4
Connector/terminal block converter module N/A - A6TBXY36 4
Cable (for connector/terminal block converter module) N/A - ACTB 4
Input module AX42 1 QX42 1
Output module AY13 5 QY41P 5
Relay terminal module N/A - A6TE2-16SRN 10
Cable (for relay terminal module) N/A - AC06TE 5
AC06TE
Model Length (L)
AC10TE AC30TE AC50TE AC100TE
L
B A 350 mm
350 mm
B-side: Second half
16 pts. (Y10 to Y1F) Unit: mm
A-side: First half
16 pts. (Y0 to YF)
* The Q312 can be used if the control panel is wide enough. With the Q312B, the I/O modules can be mounted on one base unit, eliminating the need for the Q68B extension base unit, QC06B extension cable, and one Q61P power supply module.
Note: The relay terminal module can function as a relay terminal block while performing contact outputs.
52.6
(b) Module selection example
(c) Relay terminal module (A6TE2-16SRN)
(e) Cables
The connection cables compatible with A6TE2-16SRN are shown below.
(d) External dimensions
△
○ △
△
○
△
△
○
△
△
○
Ф ○
Ф
○
○
○
○
○
○
(cos Ф =0.7): 100,000 times or more (cos Ф =0.35): 100,000 times or more △ (cos Ф =0.7): 200,000 times or more
(cos Ф =0.35): 200,000 times or more
○
0.6 m 1.0 m 3.0 m 5.0 m 10.0 m
2.1 Replace A/QnA (Large Type) Series with Q Series
ACTB
Item AY13
Number of output points Use two A6TE2-16SRN modules
when using more than 16 points.
16 points △
○: Compatible, △: Partially changed A6TE2-16SRN
Compati-bility Remarks
32 points
Isolation method The isolation method differs, but the
isolation performance is equivalent.
The electrical life of the A6TE2-16SRN is half of the AY13's life. However, the relay for the A6TE2-16SRN can be replaced.
Relay △
Photocoupler
External power supply
Wiring modification is required.
The supplied current value will be larger.
24 V DC ±10%
Ripple voltage: 4 Vp-p or less ○ 24 V DC ±10%
Ripple voltage: 4 Vp-p or less
350 mA
(TYP. 24 V DC, all points ON) △ 290 mA
(TYP. 24 V DC, all points ON) Electrical
Rated switching voltage/current load: 100,000 times or more △ Rated switching voltage/current
load: 200,000 times or more Maximum switching
voltage
264 V AC
125 V DC ○
264 V AC 125 V DC
External connections 38-point screw terminal block
(M3 screw) (M3 × 6 screws) △ 38-point terminal block
connector (M3 × 6 screws)
Applicable wire size 0.75 to 2 mm2 0.75 to 1.25 mm2 △
Applicable crimping terminal
R1.25-3, R1.25-MS3, R1.25-B3A, R1.25-C3A, RAV1.25-3, RAV1.25-MS3,
RAV1.25-B3A R1.25-3, R2-3, ○
RAV1.25-3, RAV2-3 Rated switching
voltage/current
24 V DC/2 A (resistive load)/point, 240 V AC/2 A (cos Ф =1)/point,
8 A/common 24 V DC/2 A (resistive load)/point, ○
240 V AC/2 A (cos Ф =1)/point, 5 A/common
Common terminal arrangement
8 points/common (common terminals:
TB19, TB21)
○ 8 points/common
(common terminals:
TB9, TB18, TB27, TB36)
Minimum switching load 5 V DC 1 mA 5 V DC 1 mA ○
Operation indicator ON indication (LED) ON indication (LED) ○ Maximum switching
frequency 3600 times/hour 3600 times/hour ○
Response time
10 ms or less ○
10 ms or less ON to OFF
OFF to ON 12 ms or less 12 ms or less ○
200 V AC 1.5 A, 240 V AC 1 A (cos Ф =0.7): 100,000 times or more
200 V AC 0.7 A, 240 V AC 0.5 A (cos Ф =0.35): 100,000 times or more
24 V DC 1 A, 100 V DC 0.1 A (L/R=7 ms): 100,000 times or more
△ 200 V AC 1.5 A, 240 V AC 1 A
(cos Ф =0.7): 200,000 times or more 200 V AC 0.7 A, 240 V AC 0.5 A (cos Ф =0.35): 200,000 times or more
24 V DC 1 A, 100 V DC 0.1 A (L/R=7 ms): 200,000 times or more Mechanical
Voltage Current
20 million times or more ○ 20 million times or more
Life
(f) Specifications comparison between AY13 and A6TE2-16SRN
•‥ Use‥the‥Q‥Series‥large‥type‥input‥module‥QX21L‥to‥replace‥the‥modules‥without‥changing‥the‥
wiring.
Note‥that‥if‥the‥Q‥Series‥large‥type‥base‥unit‥cannot‥be‥used‥because‥of‥space‥limitations‥in‥the‥
panel‥or‥because‥of‥the‥module‥configuration,‥etc.,‥replacements‥can‥be‥completed‥easily‥by‥
using‥the‥FA‥goods.
•‥ A‥dedicated‥cable‥is‥available‥to‥connect‥the‥programmable‥controller‥with‥the‥FA‥goods,‥so‥
there's‥no‥need‥to‥prepare‥cables‥when‥making‥a‥replacement.
• The FA goods input module has a function to convert 200 V AC input signal into 24 V DC, so select a 24 V DC input connector type module for the programmable controller side input module.
• The following products are available for the FA goods.
Triac large capacity (1 A/point) output module Transistor large capacity (2 A/point) output module Common multi-point I/O module
The FA goods can be used when replacement using the Q Series large type I/O module conversion adapter is difficult.
For details on the FA goods manufactured by Mitsubishi Electric Engineering Co., Ltd., please contact your local Mitsubishi sales office or representative.
• To replace using existing external wiring terminal block, use the Q Series large type input module QX21L.
Refer to "2.1.2 Upgrade to Q Series using Q Series large type base unit and I/O modules" for details.
Replace
(3) Replace A/QnA (Large Type) Series 200 V AC input module AX21
[Use FA goods (manufactured by Mitsubishi Electric Engineering Co., Ltd.)]
The following is an example of replacing the A (Large Type) I/O module with the Q Series using FA goods.
●‥Instruction
(1) Using the FA goods, convert the 200 V AC input into 24 V DC, and lead it in with QX41, etc.
(2) The external wiring will change, but program does not need to be changed since the I/O address is the same. (3) The following FA goods are used.
●‥System‥configuration‥example
●‥Connection‥cable
●‥Module‥selection‥example Power supply moduleProduct name CPU module
Input module Main base unit
Existing model Replacement model 1
1