メジャースコープeasure Scope 画像認識用レンズmage recognition lens エアピットir Pit
M I A
カスタムメイドustom madeC
顕微鏡から接眼レンズを外し、直接鏡筒に差し込んで 使用するCマウントアダプターです。低価格ですので、
モニター上にワークを映し出すだけの簡単な検査に お気軽にご利用いただけます。画像データ目安表を ご参照のうえ、お選びください。
The Direct C-Mount Adapter can be mounted directly onto the lens, after removing the eyepiece. Its low cost means that it can be used for simple inspections where the work-piece only needs to be displayed on a monitor.
Select after referring to the image data guide table.
ガラスを組み込むことができます。視度補正機能により視力 に合わせた目盛線のピント合わせが可能です。また、周辺からの 光をカットすることで見やすく、目の疲労を軽減する接眼フード もアクセサリーとしてご用意しております。
scale marks to be focused to match the operator’s vision.
Also, an optional eyepiece hood is available to cut ambient light and improve visibility and reduce eye fatigue.
画像観察への簡単な応用 Simple application in image observation
ダイレクト式 C マウントアダプター D-CA Direct Lens C-Mount Adapter
●リレーレンズ式Cマウントアダプターのデータ目安表 Relay Lens C-Mount Adapter data guide table
接眼レンズ
Eyepiece lens
対物レンズ
Objective lens
実視野(縦×横×対角)mm
Field of vision (vertical × horizontal
× diagonal) mm
モニター倍率
(9 インチモニター上)
Monitor magnification (on 9 inch monitor)
Working distance作動距離
OCD
10 ×
OBD 1 × 4.5 × 6 × 7 約 29.6 × 約 176mm 2 × 2..25 × 3 × 3.5 約 58 × 約 85mm 3 × 1.5 × 1.95 × 2.3 約 86 × 約 63mm 4 × 1.1 × 1.5 × 1.75 約 118 × 約 48mm 5 × 0.9 × 1.2 × 1.4 約 147 × 約 39mm 6 × 0.75 × 0.95 × 1.2 約 172 × 約 33mm 8 × 0.55 × 0.72 × 0.9 約 232 × 約 27mm 10 × 0.45 × 0.6 × 0.7 約 296 × 約 20mm
接眼レンズ
Eyepiece lens
対物レンズ
Objective lens
実視野(縦×横×対角)mm
Field of vision (vertical × horizontal
× diagonal) mm
モニター倍率
(9 インチモニター上)
Monitor magnification (on 9 inch monitor)
Working distance作動距離
OCD
20 ×
OBD 1 × 2.25 × 3 × 3.5 約 58 × 約 176mm 2 × 1.125 × 1.5 × 1.75 約 116 × 約 85mm 3 × 0.75 × 0.975 × 1.15 約 172 × 約 63mm 4 × 0.55 × 0.75 × 0.875 約 236 × 約 48mm 5 × 0.45 × 0.6 × 0.7 約 294 × 約 39mm 6 × 0.375 × 0.475 × 0.6 約 344 × 約 33mm 8 × 0.275 × 0.36 × 0.45 約 464 × 約 27mm 10 × 0.225 × 0.3 × 0.35 約 592 × 約 20mm
●ダイレクト式Cマウントアダプターのデータ目安表 Direct C-Mount Adapter data guide table
2/3インチCCDカメラ使用時 When 2/3" CCD camera is used
対物レンズ
Objective lens
実視野(縦×横×対角)mm
Field of vision (vertical × horizontal
× diagonal) mm
モニター倍率
(9 インチモニター上)
Monitor magnification (on 9 inch monitor)
Working distance作動距離
OBD 1 × 4.2 × 5.3 × 6.3 約 32 × 約 150mm 2 × 2..28 × 2.9 × 3.5 約 60 × 約 80mm
3 × 1.6 × 2 × 2.4 約 85 × 約 61mm
4 × 1.2 × 1.55 × 1.9 約 112 × 約 48mm 5 × 1 × 1.25 × 1.5 約 136 × 約 39mm 6 × 0.82 × 1.05 × 1.3 約 162 × 約 33mm 8 × 0.62 × 0.8 × 0.95 約 216 × 約 24mm 10 × 0.5 × 0.65 × 0.8 約 264 × 約 20mm 1/2インチCCDカメラ使用時 When 1/2" CCD camera is used
対物レンズ
Objective lens
実視野(縦×横×対角)mm
Field of vision (vertical × horizontal
× diagonal) mm
モニター倍率
(9 インチモニター上)
Monitor magnification (on 9 inch monitor)
Working distance作動距離
OBD 1 × 3.1 × 4.1 × 4.9 約 42 × 約 150mm 2 × 1.7 × 2.2 × 2.6 約 78 × 約 80mm 3 × 1.2 × 1.55 × 1.85 約 110 × 約 61mm 4 × 0.9 × 1.18 × 1.4 約 147 × 約 48mm 5 × 0.75 × 0.95 × 1.15 約 180 × 約 39mm 6 × 0.61 × 0.81 × 0.98 約 214 × 約 33mm 8 × 0.48 × 0.6 × 0.73 約 286 × 約 24mm 10 × 0.4 × 0.5 × 0.6 約 350 × 約 20mm
M-45鏡筒光学系使用時の実測値データです。
TVモニターのサイズを大きくすれば、モニター倍率はその比率分だけ大きくなり ます。(実視野は変わりません)
Actual data from use with M-45 Optical lens system.
M-45鏡筒光学系・2/3インチCCDカメラ使用時の実測値データです。
TVモニターのサイズを大きくすれば、モニター倍率はその比率分だけ大きくなり ます。(実視野は変わりません)
Actual data from use with M-45 Optical lens system, with 2.3 inch CCD camera.
C マウントアダプターの画像データ目安表 C-Mount Adapter Image Data Guide Table
CCDカメラ等の電子倍率が掛かって拡大されますので、顕微鏡を肉眼で観察する場合に比べてモニターに映る実視野は狭くなります。
Because the image is magnified electronically, by CCD camera, etc., the field of vision displayed on the monitor becomes narrower in comparison with observation through a microscope with the naked eye.
※φ28用とφ30用の2種類がございます。
※There are 2 types ofφ28 andφ30.
MS
MEASURE SCOPEリ溝式ステージ Dovetail Stage ジャースコープ Measure Scope 像認識用レンズ
Image recognition lens アピット
Air Pit
ア
メ
画
エ
こだわりの機能性、簡単な操作性
Committed functionality, easy usability
スタムメイド
Custom made
カ
このDH-Sデジカメアダプターをメジャースコープに装着する ことで、市販の安価なコンパクトデジタルカメラをそのまま 利用して写真撮影することができます。また、デジカメの持つ ズーム機能により拡大映像にすることも可能です。デジカメの 液晶画面を利用し、簡易的なモニタースコープにもなります。
By mounting a measure scope on the DH-S digital camera adapter, a cheap and compact commercially available digital camera can be used to photograph images. Also, the normal zoom function of the digital camera can be used to enlarge images. The digital camera’s LCD can become a simple micro- scope monitor.
メジャースコープ用デジカメアダプター Digital camera adapter for a measure scope
市販のデジカメで顕微鏡画像を撮影
Photographing microscope images with a commercially available digital camera
DH-S
使用例
Examples(OCD10×の例)
(OC 20×の例)
(OC 15×の例)
11〜80
112
±45
88
58 112 25〜94
23〜44 21〜91
デジカメアダプター 目盛・標準時 For digital camera adapter
Scale-standard
デジカメアダプター 目盛・ズーム時 For digital camera adapter Scale-zoom
メジャースコープeasure Scope 画像認識用レンズmage recognition lens エアピットir Pit
M I A
カスタムメイドustom madeC
58718829
φ16.8 φ19.8
10 818 579 φ19.8
φ16.8
21
8
818
φ16.8
571.5
φ19.8
27.5
6
818
φ16.8
565
φ19.8
21
5
818
φ16.8
556
φ19.8 21 4
818
φ19.8
5
φ16.8
427
3 M20.32
511.5
φ19.8
20.5
OBD 1x、2xレンズ OBD 3xレンズ OBD 4xレンズ OBD 5xレンズ OBD 6xレンズ OBD 8xレンズ OBD 10xレンズ 36山ねじ M20.32 36山ねじ M20.32 36山ねじ M20.32 36山ねじ M20.32 36山ねじ M20.32 36山ねじ M20.32 36山ねじ
0.5
22 15
7 10 13 OBD3〜6×用
M3六角穴付きボルト
10.5 13 7
φ22.5 φ19.85 14.5
0.522
M3六角穴付きボルト 22 OBD1〜2×用
RMB‑1〜2X
RMB‑3〜6X
透明ガラス
5.7 6
3
n19.8
8.5
n16.8n17.5
n10
OB1×,OB2×に装着
PGC‑1〜2X
OB3×〜OB10×に装着
PGC‑3〜10X 対物レンズの先に取り付け、ミラー
の反射で光軸を90°に曲げて側視が できます。ワーク側面や機械内部の 観察などに有効です。(像はミラー 反転像になります)
Attached to the front of the objective lens, the scope bends the optical axis 90º, so the image can be viewed from the side. This
is useful for viewing the side of a work- piece or inside a ma- chine. (The image is inverted.)
対物レンズの先に取り付け、レンズの表面をホコリや汚れから 保護するためのキャップです。特に機械周辺など油が飛散する ような環境では、油浸によるレンズの劣化を防ぐのに効果的です。
汚れたガラス板は簡単に交換できます。(10 枚入り交換ガラス セットは別売)
Attached to the front of the objective lens, the cap protects the lens surface from dust and dirt. The cap is particularly useful in preventing lens deterioration due to oil contamination when used in environments where there may be a lot of airborne grease.
Soiled glass plates can be easily replaced. (A set of 10 spare glass plates is sold separately.)
反射ミラーボックス Reflector box
( )
1×~ 2×用 / For 1× to 2×3×~ 6×用 / For 3× to 6×
反射ミラーボックス Reflective scope box 保護ガラスキャップ Protective glass cap
弊社の対物レンズは厳密な倍率補正にも対応し、接眼ミクロ メーターと組み合わせて計測した際には精度の高い測定を行う ことができます。また、専用Cマウント接写リングアダプター を取り付けることで直接CCDカメラへの接続が可能となり、
低コストで画像観察レンズやバリフォーカルレンズとしての 応用もできるようになります。(P70 参照)
Miruc objective lenses are enabled for strict magnification correction and, when combined with an eyepiece, can be used for very high-precision measurement. Using the special C- mount ring adapter, the lens can be directly attached to a CCD camera, enabling it to be used as a low cost image ob-
servation lens and variable focus lens (see P70).略称OBD Short name : OBD
対物レンズ 略称 OBD
MS
MEASURE SCOPEリ溝式ステージ Dovetail Stage ジャースコープ Measure Scope 像認識用レンズ
Image recognition lens アピット
Air Pit
ア
メ
画
エ
こだわりの機能性、簡単な操作性
Committed functionality, easy usability
スタムメイド
Custom made
カ
120°90°
55°60°
0102030405060708090100110120
0102030405060708090100
00101234 678910
20 30
40506070 8090 80 706050 40 30
20
100
5
123456
1 2 3 4 5
6 1
2 3 4 5 6
1
3
5 2
4
6
0.70.9 0.6 0.8 1
1.522.533.5 44.55
10 20 15
0.40.2 0.30.5 0.1
60708090 100 50 40 30 20 10 0
10r
20r 30r
40r r 50 60r
70r80r90r
12345678910
1 2 3 4 5 6
10987
260 250 240 230
220 210200 190180170160150140
130 120
110 100 270
280 290 300 310
320330340 350010 20 30
40 50
60 70 80 90
31-A
31-E
31-I 31-B
31-F
31-J
31-C
31-G
31-K 31-D
31-H
12mm120等分目盛
(最小目盛0.1mm)
十 字 線、55 °、60 °、
90°、120°角度線 12 mm scale in 120 increments (minimum increment 0.1 mm) Crosshairs, 55°, 60°, 90°, 120° angle lines
1mm同芯円と十字線 1 mm concentric circles and crosshairs
十字線縦・横線上に 12mm120等分目盛
(最小目盛0.1mm)
12 mm scale in 120 increments on vertical and horizontal crosshairs (minimum increment 0.1mm)
角度・同芯円・目盛 Angles, concentric circles, scales
RゲージR gauge
10mm10等分方眼 10 mm grids equally divided into 10 360°角度 360° angle 十字線横線上に 10mm100等分目盛
(最小目盛0.1mm)
10 mm scale in 100 increments on horizontal crosshairs
(minimum increment 0.1mm)
180°分度器 180° protractor 十字線のみ Crosshairs only
10mm100等分目盛
(最小目盛0.1mm)
10 mm scale in 100 increments (minimum increment 0.1mm)
仕様
ガラス径・・・・・・・・・・・・・・φ24 材質・・・・・・・・・・・・・・・・・・青板ガラス 板厚・・・・・・・・・・・・・・・・・・1mm クロム蒸着・・・・・・・・・・・・上面 Specifications
Glass diameter: φ24
Material: Blue plate glass
Plate thickness: 1 mm Chromium vapor deposition: Top surface
「観る・測る」をもっと使いやすく
Making “viewing and measuring” easier
メジャースコープeasure Scope 画像認識用レンズmage recognition lens エアピットir Pit
M I A
カスタムメイドustom madeC
特注ミクロメーターの製作依頼で、『1目のピッチをもっと細かく したい』とのご要望がよくあります。1目の読みを細かくするので あれば、上記のように使用する対物レンズを交換することで対応でき ます。しかし、実際に加工する刻み方を細かくする場合には注意が 必要です。最小1目の刻みが通常の半分である0.05mmピッチまでなら 肉眼でも読み取りが容易ですが、刻みが0.05mmピッチ以下になると肉 眼での判別が難しくなります。
接眼レンズ20×を使用すれば0.05mm ピッチ以下でも読み取りやすく はなりますが、標準の接眼レンズ10×と比べて視野が狭くなる等、
使用上の制限が生じることになります。
このように接眼ミクロメーターの1目盛の読みは、実際の加工で 刻まれているピッチと対物レンズの倍率との関係で決まります。
ご要望に応じた正確な測定のできるミクロメーターの選択や特注製品
We often receive requests to manufacture a special order micrometer with “the first pitch being the smallest”. If the first pitch needs to be the smallest, this can be done by replacing the objective lenses, as de- scribed above. However, care needs to be taken when making the incre- ments smaller in actual processing. If the smallest increment is made 0.05 mm, which is half of the normal pitch, it can still be read with the naked eye, but any smaller than 0.05 mm would be difficult to judge with the naked eye.
If objective lens 20× is used, pitch of less than 0.05 mm can be read easily, but there may be limitations in actual use, such as a much nar- rower field of vision when compared with the standard objective lens 10×.
Therefore, the reading of a single increment of the eyepiece micrometer depends on the relationship between the pitch cut in actual processing and the objective lens magnification.
We would advise our customers to give careful consideration to these calculations when selecting micrometers to give correct measurements as required, and when making special orders.
対物レンズ2×使用時 0.1÷ 2 =0.05mm (最小1目の読み)
対物レンズ5×使用時 0.1÷ 5 =0.02mm (最小1目の読み)
対物レンズ10×使用時 0.1÷10=0.01mm (最小1目の読み)
With objective lens 2×, 0.1 ÷ 2 = 0.05 mm (minimum increment) With objective lens 5×, 0.1 ÷ 5 = 0.02 mm (minimum increment) With objective lens 10×, 0.1 ÷ 10 = 0.01 mm (minimum increment)
ます。お客様の仕様に基づいた特注ミクロメーターの製作も 随時承っております。(特注ミクロメーター受注実績1000種類 以上)
Micrometers can be custom-produced to the customer’s indi-
vidual specifications. (Miruc has already produced over 1,000types of custom ordered micrometers.)
1目盛の読みの換算方法と注意点
1 Scale reading conversion and caution接眼ミクロメーターの着脱方法
How to remove the eyepiece micrometer接眼ミクロメーターの目盛の読みは、実際に刻まれている最小1目の 間隔を使用する対物レンズの倍率で割ると算出できます。
例として31-E(10mm100等分= 最小1目0.1mm 刻み)では、以下の ようになります。
The eyepiece micrometer scale readings can be calculated by taking the smallest increment cut on the scale and dividing it by the magnification of the objective lens.
As an example, the 31-E ( 10 mm in 100 increments = minimum increment 0.1 mm) would be read as follows.
1. 固定用セットネジ①を緩めると、接眼レンズ系 全体②が鏡筒光学系から抜き取れます。
2. 接眼ミクロメーター(目盛ガラス)の着脱は、左図 接眼レンズの③部をネジ回転することにより ホルダーが取り外せます。取り外したホルダー の目盛ガラス抑え枠④をさらにネジ回転で取り 外せば、接眼ミクロメーターの着脱ができます。
1. Loosen the locking screw ① and the whole eye- piece lens ② can be removed from the microscope optical system.
2. To remove the eyepiece micrometer (scale glass), unscrew the eyepiece lens ③ illustrated at left and take off the holder. Hold the scale glass on the holder in place and continue to unscrew the frame. ④ Now the eyepiece micrometer can be removed.
2
①
②
③
④ 目盛ガラス なお、メジャースコープと一緒に接眼ミクロメーターもご注文いただきました際は、弊社調整室できれいに組み込んで出荷して おります。接眼ミクロメーターのみ単独でご購入になった場合や、接眼ミクロメーターを交換してご利用になる場合などには、
上記方法にてお取り扱いください。
Note that, if an eyepiece micrometer is ordered together with a measure scope, it is properly fitted in our workshops before shipment. If you have purchased the eyepiece micrometer by itself, or need to replace the eyepiece micrometer, remove/ attach the unit as described above.
(例)Example
MS
MEASURE SCOPEリ溝式ステージ Dovetail Stage ジャースコープ Measure Scope 像認識用レンズ
Image recognition lens アピット
Air Pit
ア
メ
画
エ
こだわりの機能性、簡単な操作性
Committed functionality, easy usability
スタムメイド
Custom made
カ
MG スタンド MG stand MX-S スタンド MX-S stand
MY-S スタンド MY-S stand FA-S スタンド FA-S stand
機械や装置にも簡単に取り付けられる マグネットスタンドです。
造りが頑丈ですので、ハードな作業現場では必需品です。
This is a magnet stand that can be easily attached to machinery and devices. It is of robust construction and is a must have for harsh working conditions.
MXスライダーをマグネット式に組み合わせたスタンドです。方向 セットも自在で三軸に摺動しますので、鏡筒光学系のX・Y・Z への 敏速な移動や位置決め調整などの用途に大変便利です。
The MX slider is combined with a magnetic stand. It has a triple axle sliding action for orientation setting, which means that it is very useful for moving quickly in any of the X, Y or Z directions of the microscope optical unit, and for positioning adjustment, etc.
MYスライダーをマグネット式に組み合わせたシンプル なスタンドです。
This is a simple stand that features a combination of the MY-slider and a magnetic stand.
FAスライダ ーをマグ ネット式 に 組 み 合 わ せ た ス タ ンド で す。屈 折 機 構 部 は180 °傾 斜・360 ° 回 転 が 可 能 で す の で、 作 業 状 況 に 合 わ せ て 鏡筒光学系を任意の角度にセットすることができます。
This stand is a combination of the FA slider with a magnetic stand. It has an articulated construction that allows 180°
tilting and 360° rotation, so that the lens barrel can be freely set at whichever angle is required by the operating con- ditions.
(148)
74
76
55 7.592 φ14
39
39 φ171973485
117
(130)
(316)
φ22214
(245)
31
28.3
50 締付け棒
(付属品)
52 30
42
φ20
3233485 55
50
117
(130)
φ14
(442) 31.2 (82)
(20.3)
248.5 4
22 51
(10)
φ32
(148) (10) 123 70 204
φ32
28.5
39
39 φ171973485 (316)
74 φ22
55
191.5〜376 71.5 100.5
多種多様な目的に応じた、豊富なラインナップ
A full product lineup to match a rich diversity of needs
(20.3)
31.2 45 94.526.830(182.3)21(10)42
241.5
72
50
55
44
117
8534323
φ20
(442)
(130)
3531(66)
φ32
φ14
短いタイプ 60mm 長いタイプ 248.5mm Short type 60mm Long type 248.5mm
メジャースコープeasure Scope 画像認識用レンズmage recognition lens エアピットir Pit
M I A
カスタムメイドustom madeC
滑らかな水平移動により広範囲に わたる観察に適しています。
機械や装置の光学系セッ ティングゲージとして、
マグネット固定位置から 必要に応じて横にスライド させ顕微鏡で観察ができます。
また観察後すぐ元の位置 に戻せば、作業の妨げにも なりません。
Smooth horizontal movement is ideal for ob- servation covering a wide range. As an optical setting gauge of a machine or de-
vice, the microscope can be slid horizontally from the magnetic fixed position for viewing. Also, once viewing is finished, the unit can be easily returned to its original position, causing no hin- drance to work.
7049 35 514260
132〜302±10
φ24
φ16
(130)117
60
φ32 (10)
50〜297 35 80
50 601415 30 18
φ10 50 55
50 60〜307 50
40
FR スタンド FR stand LSB スタンド LSB stand
MSS スタンド MSS stand MST スタンド MST stand
アームが柔軟に動くので、鏡体ユニットのセッティングが自在に できます。センターロックノブを締めると、3 箇所のアーム間接部の 屈曲が同時に強力に固定できます。斜め方向からの観察や、頻繁に セット位置を変更する場合に大変便利です。
The arm’s flexible movement allows the scope unit to be posi- tioned freely. The center locking knob can be tightened to secure the three sections of the arm in place. This stand is very con- venient when an object has to be viewed
obliquely, or when the position has to be changed frequently.
シンプルで低価格の卓上 用白黒板スタンドです。
白黒板はつや消しマット 調仕上げで、設置する 床面の反りやベースとの ガタツキ・平面度を補正 する安定度調整機能が 付いています。
This is a simple, low cost desktop stand with a black and white, matt finish board. The stand has a stability adjust- ment function to com-
pensate for any warping or uneven-
精密部品や工具類の測定・検査 に最適な高級研磨定盤付き スタンドです。反り・ガタツキ・
平面度を補正する安定度調整 機能が付いています。
This stand has a high grade polished surface table, ideal for the measurement or in- spection of precision parts and tools.
It is also equipped with a sta- bility adjustment function to compensate for any warping or unevenness of the floor surface on which the base is installed.
φ14 24
(75)
71.514
65
163(102.5) 55
50 117
(130)
113
2202246414
42
(8.4)
60 30
(192)
144
60
φ14
φ23.8
φ20.8
70 (324)
φ89.8
2026414224 100
100
60
φ20.8 φ23.8
φ14
144
(192)
90 42
8 (324)
利便性の高いマグネットスタンド、部品や基板の検査などに 最適な卓上用スタンドが多数ラインナップされております。
目的や用途に合わせてお選びください。
and remove in manufacturing workplaces and with machin- ery and devices, and desktop stands that are ideal for work such as the inspection of components and boards, etc.
Choose the stand that best suits your purpose and needs.
MS
MEASURE SCOPEリ溝式ステージ Dovetail Stage ジャースコープ Measure Scope 像認識用レンズ
Image recognition lens アピット
Air Pit
ア
メ
画
エ
こだわりの機能性、簡単な操作性
Committed functionality, easy usability
スタムメイド
Custom made
カ
SP14-B スタンド SP14-B stand
鏡体ユニットの取り付け方向や角度のバリエー ションが広がる便利な継ぎ手です。
This handy joint allows greater variation in the scope unit attachment orientation and angle.
MH サイドアーム MH side arm
鏡体ユニットの取り付け方向 や角度のバリエーションが 広がる便利な継ぎ手です。
This handy joint allows greater variation in the scope unit attachment ori- entation and angle.
φ14 30
90 17
28 3314142.562
20 121
φ14
φ14
メジャースコープeasure Scope
DXY スタンド DXY stand
ステージサイズ100×100mm、ストローク±12.5mmのXY精密ステージ 付きスタンドです。デジタルマイクロ仕様ですので、測定の基準となる ゼロセットや数値の読み取りも簡単です。
オプションのDXY-KPを取り付ければ、低価格で簡単に回転機能が 付加され、水平基準合わせや観察・検査が大変便利になります。
This stand comes with a 100 × 100 mm XY precision stage with a
±12.5 mm stroke. It has digital microscope specifications, making it simple to set zero as the measurement reference position, and to read off numeric values.
By attaching the option DXY-KP, a low cost and simple rotation function can be added, extremely useful for horizontal reference alignment and observation and inspection.
MES スタンド MES stand
X軸65mm・Y軸25mm 摺動の簡易メカ付きスタンドです。
ワークをスムーズに移動できるので、測定・検査が効率的に行え ます。反り・ガタツキ・平面度を補正する安定度調整機能が付いて います。
This stand is provided with a simple mechanism allowing sliding of 65 mm along the X axis and 25 mm along the Y axis. Smooth movement of the work piece allows for more effi-
cient measurement and inspection.
The stand is equipped with a stability adjustment function to compensate for any warping or un- evenness of the floor surface on which the base is installed.
1464202224
124(32.6)
42
(8.4)
144
60
φ14
φ23.8
φ20.8 (324)
90
(192)
60
010 10
010203040506070 0102030 144
M16×1 4643641464
40
90 192
202
深さ6
φ23.5 φ14
2525(11)
4-M4深さ6 8-M4深さ5MAX 170
(11) 90 100 移動距離±12.5 移動距離±12.5
100 90 25 25 MAX 170
MOP スタンド MOP stand
MH サイドアーム付きで広範囲に鏡体ユニットを移動できる 大型スタンドです。
This large sized stand has an MH side arm that allows the scope unit to be moved over a
wide range. 90 14 23869
330
28020 (334)7
φ14
φ20.8 φ23.8
250
62
φ14
DXY-KP
φ14
A-A
A A
22226 (12.5)2225
38 25 3.6
φ12
4.5 8