• 検索結果がありません。

電子回路論11

N/A
N/A
Protected

Academic year: 2021

シェア "電子回路論11"

Copied!
11
0
0

読み込み中.... (全文を見る)

全文

(1)

Electronic circuit

電子回路論 11

ats.issp.u-tokyo.ac.jp

勝本信吾

(2)

増幅回路と雑音

等価雑音帯域幅 (equivalent noise band width)

減衰傾度 k -6 db/oct 1.57 -12 db/oct 1.11 -18 db/oct 1.05 -24 db/oct 1.03

gain band width GBW

=A (open loop gain)×fc

OP ampの規格表などに出ているもの

fc は,帰還回路により変化する.

(3)

非反転増幅回路と雑音

1. 𝑅𝑆の熱雑音 = 4𝑘𝑘𝑅𝑆

2. 𝑅𝑓1 ∥ 𝑅𝑓2で発生する熱雑音 = 4𝑘𝑘(𝑅𝑓1 ∥ 𝑅𝑓2) 3. 入力換算雑音電圧 𝑒𝑛, 入力換算雑音電流 𝑖𝑛

4. 入力換算雑音電流と信号源抵抗による雑音 = 𝑖𝑛 × 𝑅𝑆

5. 入力換算雑音電流と帰還抵抗による雑音 = 𝑖𝑛 × (𝑅𝑓1 ∥ 𝑅𝑓2)

(4)

非反転増幅回路と雑音

(出力雑音)

= 𝑒12 + 𝑒22 + 𝑒32 + 𝑒42 + 𝑒52 × 𝐺 × 等価雑音帯域幅

(5)

NF マッピング

(6)

その他の雑音 : バルクハウゼン雑音

(7)

ポップコーン雑音

Popcorn noise, Burst noise

pn junction

2準位系

(8)

ランダム性雑音の振幅分布

(9)

Popcorn noise の振幅分布

(10)

アバランシェ雑音

Avalanche Photo-Diode (APD) avalanche or Zener breakdown

Zener voltage standard diode

white noise

(11)

練習問題 5-1

パラメタ 単位

A 146 dB

GBW 110 MHz

𝑒𝑛 (1kHz) 0.9 nV/ Hz 𝑖𝑛 (1kHz) 2 pA/ Hz

OP アンプ AD797 の特性は次のようになっている

上のような非反転増幅回路で,𝑅𝑆= 100 Ω,𝑅𝑓1=50 Ω,

𝑅𝑓1=49.95 kΩ ,高周波の減衰傾度を− 6 dB/octとした時の,

300Kでの出力雑音電圧を求めなさい.

ヒント:アンプの電圧ゲインは1000, これとAとGBWから

𝑓𝑐が求まる(1000倍に落としたことによる𝑓𝑐 の増加に注意).

−6 dB/octの場合の雑音帯域幅はこれに1.57をかける.

参照

関連したドキュメント

♦ Cycle−by−cycle peak current limit: when the current sense voltage exceeds the internal threshold V ILIM , the MOSFET is immediately turned off.. ♦ Winding or Output

(現 連結子会社 FUJIFILM North America Corporation) 1966年6月 Fuji Photo Film (Europe) GmbH をドイツに設立。.. (現 連結子会社 FUJIFILM

• Therefore, each output voltage is its secondary peak voltage times the duty ratio of the primary bus voltage, +Bus, (neglecting diode drops and Q2’s ON voltage).. 5 V, 10 A 12 V,

During the turn-off transient, boost inductor current changes the path from MOSFET to output diode and before the output diode turns on; a minor voltage peak can be shown at

During the turn-off transient, boost inductor current changes the path from MOSFET to output diode and before the output diode turns on; a minor voltage peak can be shown at

The maximum zener current I ZM should be considered the maximum reverse current recommended by the manufacturer. This plateau region has, however, a large positive slope such that

電路使用電圧 300V 以下 対地電圧 150V 以下: 0.1MΩ 以上 150V 以上: 0.2MΩ 以上 電路使用電圧 300V 以上 : 0.4MΩ 以上.

Photo Credits:Stefanos Tsakiris Copyrightⓒ ECSCRM2016 Conference Photo Credits:Stefanos Tsakiris Copyrightⓒ ECSCRM2016 Conference.