• 検索結果がありません。

Avoid prolonged contact with skin. In case of contact with eyes, immediately flush with water for at least 15 minutes and get medical attention.

N/A
N/A
Protected

Academic year: 2022

シェア "Avoid prolonged contact with skin. In case of contact with eyes, immediately flush with water for at least 15 minutes and get medical attention."

Copied!
2
0
0

読み込み中.... (全文を見る)

全文

(1)

Net Contents: 1 U.S. Gallon C A U T I O N

Keep Out of Reach of Children

Avoid prolonged contact with skin. In case of contact with eyes, immediately flush with water for at least 15 minutes and get medical attention.

STORE ABOVE 45° F

Principal Functioning Agents: pct./wt.

Proprietary blend of active foaming agents and formulation aids...100.0%

CORNBEL T ®

ULT RA -MA RK

FOAM MARKER

(2)

CORNBELT® ULTRA-MARK is specially formulated with a unique blend of high foaming surfactants and foam stabilizers that delivers a long lasting foam, particularly under adverse hot and windy application conditions and in hard water.

CORNBELT® ULTRA-MARK produces foam that is resistant to wind allowing the foam ball to be resilient to the degrading effects of moderate wind.

CORNBELT® ULTRA-MARK can be used with any foam marker equipment. Field tests conducted using CORNBELT® ULTRA-MARK indicate that this versatile formula produces long lasting, heat-resistant foam when used with both pressurized and non-pressurized foam marking systems. This concentrate is effective at various dilution rates based on the hardness of the water. Many factors influence how long the foam will last. Foam ball size, colorants, pressure, temperature, humidity, soil type and wind velocity will impact foam life.

To insure a good quality foam, be certain to flush and clean the foam generating equipment before use.

DIRECTIONS FOR USE

For best results start by putting half of the water needed in the tank followed by the amount of CORNBELT® ULTRA-MARK needed, followed by the remaining half of the water.

The standard use rate of CORNBELT® ULTRA-MARK is one gallon of CORNBELT® ULTRA-MARK for every 100 gallon of water.

Under Soft Water conditions (less than 300 ppm) a use rate of one gallon of CORNBELT® ULTRA-MARK per 120 gallon to 160 gallon of water may provide satisfactory results.

Under Hard Water conditions (more than 1,000 ppm) a use rate of one gallon of CORNBELT® ULTRA-MARK per 80 gallon of water may be preferred for extended foam life.

Whenever a foam colorant additive is used, use one gallon of CORNBELT® ULTRA-MARK for every 80 gallon of water.

IMPORTANT

Do not mix CORNBELT® ULTRA-MARK with any other foam marker concentrate. This formula is a carefully tested blend of foam additives and stabilizers that may not be compatible with other products. A mixture with different foam concentrates will likely result in poor quality foam.

NOTICE: READ CAREFULLY

Conditions of Sale: Van Diest Supply Co. (and seller) offer(s) this product for sale subject to and buyer and all users are deemed to have accepted the following conditions of sale and warranty which may only be varied by written agreement of a duly authorized representative of Van Diest Supply Co.

Warranty Limitations: Van Diest Supply Co. warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes referred to in the use directions on the label subject to the inherent risks referred to below. Van Diest Supply Co. makes no other express warranties. THERE IS NO IMPLIED WARRANTY OF MERCHANTABILITY and there are no warranties which extend beyond the description on the label hereof.

Inherent Risks: The Directions for Use of this product are believed to be reliable and should be followed carefully. However, it is impossible to eliminate all risks associated with use. Buyer assumes all risks associated with use or application of this product contrary to label instructions or resulting from extraordinary weather conditions.

Limitation of Liability: In no case shall Van Diest Supply Co. be liable for special, direct or consequential damages resulting from the use or handling of this product and no claim of any kind shall be greater in amount than the purchase price of the product in respect of which such damages are claimed.

VAN DIEST SUPPLY COMPANY WEBSTER CITY, IA 50595

CORNBELT® and CORNBELT LOGO® are registered trademarks of Van Diest Supply Company. ULTRA-MARK is a trademark of Van Diest Supply Company.

参照

関連したドキュメント

based on theta functions and the theory of Kummer surfaces, our study is based on algebraic correspondences on hyperelliptic curves which are the liftts of algebraic

We derive a variational formulation of the model then we prove its unique solvability, which provides the existence of a unique weak solution to the adhesive contact problem..

The existence and uniqueness of solutions of the bounda- ry-contact problem of elasticity for homogeneous anisotropic media with a contact on some part of their boundaries

We find the criteria for the solvability of the operator equation AX − XB = C, where A, B , and C are unbounded operators, and use the result to show existence and regularity

Sofonea, Variational and numerical analysis of a quasistatic viscoelastic problem with normal compliance, friction and damage,

Keywords: dynamic process, viscoelastic material with damage, adhesion, bilateral frictionless contact, existence and uniqueness, fixed point.. 2010 Mathematics Subject

We present sufficient conditions for the existence of solutions to Neu- mann and periodic boundary-value problems for some class of quasilinear ordinary differential equations.. We

The analysis, which is based upon coupling theory, leads to simple bounds on Pn(t) for the M/G/l/0 and M/PH/1/0 queues and improved bounds for the special