These specifications are extracted from instruction manual of X0/X/X/X0/X. NGLISH These specifications are extracted from instruction manual of X0/X0/

(1)

Sony EMCS Co.

SERVICE MANUAL

Revision History

Ver. Date History Contents S.M. Rev._issued

985275831.pdf

Published by Tokai TEC

Ver. 1.0 2010.01

DCR-SX73E/SX83/SX83E

DIGITAL VIDEO CAMERA RECORDER

HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170

DIGITAL HD VIDEO CAMERA RECORDER

The components identified

by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

1-1. POWER SUPPLY DURING REPAIRS

1-2. PRECAUTION ON REPLACING THE VC-590 BOARD

1-3. SELF-DIAGNOSIS FUNCTION

Photo: HDR-CX150/BLACK — Official Release 2010.01 1.0 9-852-758-31

DCR-SX73E/SX83/SX83E

HDR-CX110/CX110E/CX115E/CX116E/

CX150/CX150E/CX155E/CX170

—

LEVEL

2 SERVICE NOTE (Check the following note before the service.)

US Model

Canadian Model

AEP Model

UK Model

North European Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Brazilian Model

Tourist Model

Japanese Model

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

(2)

SPECIFICATIONS

– ENGLISH –

SPECIFICATIONS

These specifications are extracted from instruction manual of

CX110E/CX115E/CX116E/CX150E/CX155E.

– ENGLISH –

System

Signal format: PAL color, CCIR standards HDTV 1080/50i specification Movie recording format:

HD: MPEG-4 AVC/H.264 AVCHD format compatible

STD: MPEG-2 PS Audio recording system:

Dolby Digital 2ch Dolby Digital Stereo Creator Photo recording format

: DCF Ver.2.0 Compatible : Exif Ver.2.21 Compatible : MPF Baseline Compatible Recording media (Movie/Photo)

Internal memory HDR-CX116E: 8GB HDR-CX150E/CX155E: 16GB “Memory Stick PRO Duo” media

SD Memory card, SDHC Memory card (Class 4, 6, 10)

When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for system management and/or application files. The capacity that a user can use is below. HDR-CX116E:

approximately 7.87 GB HDR-CX150E/CX155E: approximately 15.5 GB

Image device: 4.5 mm (1/4 type) CMOS sensor Recording pixels (photo, 4:3):

Max. 3.1 mega (2 048 × 1 536) pixels*1

Gross: Approx. 4 200 000 pixels Effective (movie, 16:9): Approx. 1 350 000 pixels*2 Effective (photo, 16:9): Approx. 1 180 000 pixels Effective (photo, 4:3): Approx. 1 570 000 pixels Lens: Carl Zeiss Vario-Tessar

25 × (Optical), 300 × (Digital) Filter diameter: 30 mm (1 3/16 in.) F1.8 to 3.2

Focal length:

f=2.5 to 62.5 mm (1/8 to 2 1/2 in.) When converted to a 35 mm still camera For movies*2*3_{: 37 to 1 075 mm (1 1/2 to 42}

3/8 in.) (16:9)

For photos: 36 to 900 mm (1 7/16 to 35 1/2 in.) (4:3)

Color temperature: [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K)

Minimum illumination

11 lx (lux) (in default setting, shutter speed 1/50 second)

3 lx (lux) (LOW LUX is set to [ON], shutter speed 1/25 second)

*1 The unique pixel array of Sony’s ClearVid and the image processing system (BIONZ) allow still image resolution equivalent to the sizes described.

*2 [ STEADYSHOT] is set to [STANDARD] or [OFF].

*3 The focal length figures are actual figures resulting from wide angle pixel read out.

Input/Output connectors

A/V Remote Connector: Component/video and audio output jack

HDMI OUT jack: HDMI mini connector USB jack: mini-AB

(HDR-CX115E/CX116E/CX155E/: output only)

LCD screen

Picture: 6.7 cm (2.7 type, aspect ratio 16:9) Total number of pixels: 230 400 (960 × 240) General

Power requirements: DC 6.8 V/7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption: During camera

recording, using LCD screen at normal brightness: HDR-CX110E/CX115E/CX116E/CX150E/ CX155E HD: 3.0 W STD: 2.1 W Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): HDR-CX110E/CX115E/CX116E/CX150E/ CX155E 50 × 56 × 106 mm (2 × 2 1/4 × 4 1/4 in.) (w/h/d) including the projecting parts 50 × 56 × 114 mm (2 × 2 1/4 × 4 1/2 in.) (w/h/d) including the projecting parts, and the supplied rechargeable battery pack attached

Mass (approx.)

HDR-CX110E/CX115E/CX116E/CX150E/ CX155E:

210 g (7 oz) main unit only 260 g (9 oz) including the supplied rechargeable battery pack

AC Adaptor AC-L200C/AC-L200D Power requirements: AC 100 V - 240 V, 50 Hz/60 Hz Current consumption: 0.35 A - 0.18 A Power consumption: 18 W Output voltage: DC 8.4 V* Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): 48 × 29 × 81 mm (1 15/16

× 1 3/16 × 3 1/4 in.) (w/h/d) excluding the projecting parts

Mass (approx.): 170 g (6.0 oz) excluding the power cord (mains lead)

* See the label on the AC Adaptor for other specifications.

Rechargeable battery pack NP-FV50 Maximum output voltage: DC 8.4 V Output voltage: DC 6.8 V Maximum charge voltage: DC 8.4 V Maximum charge current: 2.1 A Capacity

Typical: 7.0 Wh (1 030 mAh) Minimum: 6.6 Wh (980 mAh) Type: Li-ion

System

Signal format: NTSC color, EIA standards HDTV 1080/60i specification Movie recording format:

HD: MPEG-4 AVC/H.264 AVCHD format compatible

STD: MPEG-2 PS Audio recording system:

Dolby Digital 2ch Dolby Digital Stereo Creator Photo recording format

Internal memory HDR-CX150: 16GB

“Memory Stick PRO Duo” media

SD Memory card, SDHC Memory card (Class 4, 6, 10)

When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for system management and/or application files. The capacity that a user can use is below. HDR-CX150:

approximately 15.5 GB

Image device: 4.5 mm (1/4 type) CMOS sensor Recording pixels (photo, 4:3):

Max. 3.1 mega (2 048 × 1 536) pixels*1

Gross: Approx. 4 200 000 pixels Effective (movie, 16:9): Approx. 1 350 000 pixels*2 Effective (photo, 16:9): Approx. 1 180 000 pixels Effective (photo, 4:3): Approx. 1 570 000 pixels Lens: Carl Zeiss Vario-Tessar

25 × (Optical), 300 × (Digital) Filter diameter: 30 mm (1 3/16 in.) F1.8 to 3.2

Focal length:

f=2.5 to 62.5 mm (1/8 to 2 1/2 in.) When converted to a 35 mm still camera For movies*2*3_{: 37 to 1075 mm (1 1/2 to 42}

3/8 in.) (16:9)

3 lx (lux) (LOW LUX is set to [ON], shutter speed 1/30 second)

*3 The focal length figures are actual figures resulting from wide angle pixel read out.

A/V Remote Connector: Component/video and audio output jack

HDMI OUT jack: HDMI mini connector USB jack: mini-AB

LCD screen

recording, using LCD screen at normal brightness: HDR-CX110/CX150 HD: 3.0 W STD: 2.1 W Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): HDR-CX110/CX150 50 × 56 × 106 mm (2 × 2 1/4 × 4 1/4 in.) (w/h/d) including the projecting parts 50 × 56 × 114 mm (2 × 2 1/4 × 4 1/2 in.) (w/h/d) including the projecting parts, and the supplied rechargeable battery pack attached

Mass (approx.) HDR-CX110/CX150: 210 g (7 oz) main unit only 260 g (9 oz) including the supplied rechargeable battery pack

AC Adaptor AC-L200C/AC-L200D Power requirements: AC 100 V - 240 V, 50 Hz/60 Hz Current consumption: 0.35 A - 0.18 A Power consumption: 18 W Output voltage: DC 8.4 V* Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to+140 °F) Dimensions (approx.): 48 × 29 × 81 mm (1 15/16

Typical: 7.0 Wh (1 030 mAh) Minimum: 6.6 Wh (980 mAh) Type: Li-ion

Design and specifications of your camcorder and accessories are subject to change without notice. • Manufactured under license from Dolby

Laboratories.

These specifications are extracted from instruction manual of

(3)

– 3 –

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

概略仕様

– JAPANESE –

システム信号方式： NTSCカラー、EIA標準方式 HDTV 1080/60i方式ビデオ記録方式 HD画質：MPEG-4 AVC/H.264 AVCHD規格準拠 STD画質：MPEG-2 PS 音声記録方式 Dolby Digital 2ch ドルビーデジタルステレオクリエーター搭載静止画記録方式：DCF Ver2.0準拠：Exif Ver2.21準拠：MPF Baseline準拠記録メディア（動画・静止画）内蔵メモリー HDR-CX170：32GB “メモリースティック PRO デュオ” SDメモリーカード、SDHCメモリーカード (Class 4, 6, 10）容量は、１GBを10億バイトで計算した場合の数値です。また管理用ファイル、アプリケーションファイルなどを含むため、実際に使用できる容量は減少します。ご使用いただけるユーザー容量は、次のとおりです。 HDR-CX170 約31.5GB 撮像素子：4.5 mm（1/4型）CMOSセンサー記録画素数：静止画時最大310万画素相当＊1 （2 048×1 536）（4：3時）総画素数：約420万画素動画時有効画素数（16：9）：約135万画素＊2 静止画時有効画素数（16：9）：約118万画素静止画時有効画素数（4：3）：約157万画素ズームレンズ：カールツァイス　バリオテッサー 25倍（光学）、300倍（デジタル）フィルター径：30 mm F1.8 ～ 3.2 f=2.5 ～ 62.5 mm 35mmカメラ換算では動画撮影時＊2＊3_： 37 ～ 1 075 mm（16：9）静止画撮影時： 36 ～ 900 mm（4：3）色温度切り換え：［オート］、［ワンプッシュ］、［屋内］（3 200 K）、［屋外］（5 800 K）最低被写体照度： 11 lx（ルクス）（お買い上げ時、［シャッタースピード］ 1/60秒） 3 lx（ルクス）（ LOW LUX時、［シャッタースピード］ 1/30秒）＊1 ソニー独自のクリアビッド画素配列と画像処理システムBIONZにより、静止画は表記の記録サイズを実現しています。＊2 ［手ブレ補正］が［スタンダード］、または［切］のとき＊3 広角画素読み出しによる実動作値入/出力端子 A/Vリモート端子：コンポーネント、映像音声出力兼用端子 HDMI OUT端子：HDMIミニコネクタ USB端子：mini-AB 液晶画面画面サイズ：6.7 cm（2.7型、アスペクト比16：9）総ドット数：230 400ドット横960×縦240 電源部、その他電源電圧：バッテリー端子入力 6.8 V/7.2 V DC端子入力 8.4 V 消費電力：液晶画面の明るさ標準： HDR-CX170 HD：3.0 W　STD：2.1 W 動作温度：0 ℃～ 40 ℃ 保存温度：－20 ℃～ +60 ℃ 外形寸法： HDR-CX170 50 × 56 × 106 mm （突起部を含む）（幅×高さ×奥行き） 50 × 56 × 114 mm （突起部を含む、付属バッテリー装着状態）（幅×高さ×奥行き）本体質量： HDR-CX170 約210 g（本体のみ）撮影時総質量： HDR-CX170 約260 g（付属バッテリー含む） ACアダプター　AC-L200C/AC-L200D 電源：AC 100 V - 240 V、50 Hz/60 Hz 消費電力：18 W 定格出力：DC 8.4 V＊動作温度：0 ℃～ 40 ℃ 保存温度：－20 ℃～ +60 ℃ 外形寸法：約 48×29×81 mm（最大突起部をのぞく）（幅×高さ×奥行き）質量：約170 g（本体のみ）＊その他の仕様についてはACアダプターのラベルをご覧ください。リチャージャブルバッテリーパック NP-FV50 最大電圧：DC 8.4 V 公称電圧：DC 6.8 V 容量：公称容量：7.0 Wh（1 030 mAh）定格（最小）容量：6.6 Wh（980 mAh）使用電池：Li-ion 本機やアクセサリーの仕様および外観は、改良のため予告なく変更することがありますが、ご了承ください。 • ドルビーラボラトリーズからの実施権に基づき製造されています。

– ENGLISH –

SPECIFICATIONS

System

Signal format: PAL color, CCIR standards Movie recording format:

Video: MPEG-2 PS Audio recording system Dolby Digital 2ch Dolby Digital Stereo Creator Photo file format

Internal memory: 16 GB “Memory Stick PRO Duo” media SD memory card, SDHC memory card (Class 2, 4, 6, 10)

When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for system management and/or application files. The capacity that a user can use is approximately 15.5 GB. Image device

4.5 mm (1/4 type) CMOS sensor Recording pixels (photo, 4:3): Max. 3.1 mega (2 048 × 1 536) pixels*1

Gross: Approx. 4 200 000 pixels

Effective (Movie, 16:9): Approx. 1 350 000*2

pixels

Effective (Photo, 16:9): Approx. 1 180 000 pixels

Lens

Carl Zeiss Vario-Tessar 25 × (Optical), 300 × (Digital) Filter diameter: 30 mm (1 3/16 in.) F1.8 to 3.2

Focal length:

f=2.5 to 62.5 mm (1/8 to 2 1/2 in.) When converted to a 35 mm still camera For movies*2*3_{: 37 to 1 075 mm (1 1/2 to}

42 3/8 in.) (16:9)

3 lx (lux) ([LOW LUX] is set to [ON], shutter speed 1/25 second)

*1 The unique pixel array of Sony’s Clear Vid and the image processing system (BIONZ) allow still image resolution equivalent to the sizes described. *2 [ STEADYSHOT] is set to

[STANDARD] or [OFF].

*3 The focal length figures are actual figures from wide angle pixel readout.

A/V Remote Connector: Video/audio output jack USB jack: mini-AB

(DCR-SX73E: output only) LCD screen

recording, using LCD screen at normal brightness: Internal memory: 2.0 W Memory card: 2.0 W Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): 50 × 56 × 106 mm (2

× 2 1/4 × 4 1/4 in.) (w/h/d) including the projecting parts

50 × 56 × 114 mm (2 × 2 1/4 × 4 1/2 in.) (w/h/d) including the projecting parts, and the supplied rechargeable battery pack attached Mass (approx.)

AC Adaptor AC-L200C/AC-L200D Power requirements: AC 100 V - 240 V, 50 Hz/60 Hz Current consumption: 0.35 A - 0.18 A Power consumption: 18 W Output voltage: DC 8.4 V* Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): 48 × 29 × 81 mm (1 15/16

typical: 3.6 Wh (500 mAh) minimum: 3.6 Wh (500 mAh) Type: Li-ion

Laboratories.

These specifications are extracted from instruction manual of

(4)

Model information table

Model HDR-CX110 HDR-CX110E HDR-CX115E HDR-CX116E HDR-CX150 HDR-CX150E Destination US, CND, E NE, E, AUS AEP, UK AEP, UK US, CND, E, _{KR, BR} NE, E, HK, _{CH, JE}

Color system NTSC PAL PAL PAL NTSC PAL

Data copy CAM → PC CAM ← PC FP-1192 FLEXIBLE BOARD HDMI OUT Internal memory 8GB 16GB 16GB

Model HDR-CX155E HDR-CX170 DCR-SX73E DCR-SX83 DCR-SX83E

Destination AEP, UK J AEP US, KR, BR NE, E, CH

Color system PAL NTSC PAL NTSC PAL

Data copy CAM → PC CAM ← PC FP-1192 FLEXIBLE BOARD HDMI OUT Internal memory 16GB 32GB 16GB 16GB 16GB ･ Abbreviation AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model KR : Korea model NE : North European model J : Japanese model JE : Tourist model

SPECIFICATIONS

These specifications are extracted from instruction manual of

SX83.

– ENGLISH –

System

Signal format: NTSC color, EIA standards Movie recording format:

Video: MPEG-2 PS Audio recording system Dolby Digital 2ch Dolby Digital Stereo Creator Photo file format

Internal memory: 16 GB “Memory Stick PRO Duo” media SD memory card, SDHC memory card (Class 2, 4, 6, 10)

When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for system management and/or application files. The capacity that a user can use is approximately 15.5 GB.

Image device

4.5 mm (1/4 type) CMOS sensor Recording pixels (photo, 4:3): Max. 3.1 mega (2 048 X 1 536) pixels*1

Gross: Approx. 4 200 000 pixels

Effective (Movie, 16:9): Approx. 1 350 000*2

pixels

Lens

Carl Zeiss Vario-Tessar 25 X (Optical), 300 X (Digital) Filter diameter: 30 mm (1 3/16 in.) F1.8 to 3.2

Focal length:

f=2.5 to 62.5 mm (1/8 to 2 1/2 in.) When converted to a 35 mm still camera For movies*2*3: 37 to 1 075 mm (1 1/2 to 42 3/8 in.) (16:9)

3 lx (lux) ([LOW LUX] is set to [ON], shutter speed 1/30 second)

*3 The focal length figures are actual figures from wide angle pixel readout.

A/V Remote Connector: Video/audio output jack USB jack: mini-AB

LCD screen

Picture: 6.7 cm (2.7 type, aspect ratio 16:9) Total number of pixels: 230 400 (960 X 240) General

recording, using LCD screen at normal brightness: Internal memory: 2.0 W Memory card: 2.0 W Operating temperature: 0 °C to 40 °C (32 °F to104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): 50 × 56 × 106 mm

(2 × 2 1/4 × 4 1/4 in.) (w/h/d) including the projecting parts

50 × 56 × 114 mm (2 × 2 1/4 × 4 1/2 in.) (w/h/d) including the projecting parts, and the supplied rechargeable battery pack attached Mass (approx.)

AC Adaptor AC-L200C/AC-L200D Power requirements: AC 100 V - 240 V, 50 Hz/60 Hz Current consumption: 0.35 A - 0.18 A Power consumption: 18 W Output voltage: DC 8.4 V* Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to + 60 °C (–4 °F to +140 °F) Dimensions (approx.): 48 X 29 X 81 mm (1 15/16

typical: 3.6 Wh (500 mAh) minimum: 3.6 Wh (500 mAh) Type: Li-ion

(5)

– 5 –

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

Caution

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.

注意電池の交換は，正しく行わないと破裂する恐れがあります。電池を交換する場合には必ず同じ型名の電池又は同等品と交換してください。使用済み電池は，取扱指示に従って処分してください。

Unleaded solder

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to about 350°C.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270°C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering. 1. 注意事項をお守りください。サービスのとき特に注意を要する個所については，キャビネット，シャーシ，部品などにラベルや捺印で注意事項を表示しています。これらの注意書き及び取扱説明書等の注意事項を必ずお守り下さい。 2. 指定部品のご使用をセットの部品は難燃性や耐電圧など安全上の特性を持ったものとなっています。従って交換部品は，使用されていたものと同じ特性の部品を使用して下さい。特に回路図，部品表に0印で指定されている安全上重要な部品は必ず指定のものをご使用下さい。 3. 部品の取付けや配線の引きまわしはもとどおりに安全上，チューブやテープなどの絶縁材料を使用したり，プリント基板から浮かして取付けた部品があります。また内部配線は引きまわしやクランパによって発熱部品や高圧部品に接近しないよう配慮されていますので，これらは必ずもとどおりにして下さい。 4. サービス後は安全点検をサービスのために取外したネジ，部品，配線がもとどおりになっているか，またサービスした個所の周辺を劣化させてしまったところがないかなどを点検し，安全性が確保されていることを確認して下さい。 5. チップ部品交換時の注意・取外した部品は再使用しないで下さい。・タンタルコンデンサのマイナス側は熱に弱いため交換時は注意して下さい。 6. フレキシブルプリント基板の取扱いについて・コテ先温度を270℃前後にして行なって下さい。・同一パターンに何度もコテ先を当てないで下さい。（3回以内）・パターンに力が加わらないよう注意して下さい。

サービス，点検時には次のことにご注意ください。

無鉛半田について

本機には無鉛半田が使用されています。無鉛半田を使用している基板には，無鉛（Lead Free）を意味するレッドフリーマークがプリントされています。（注意：基板サイズによっては，無鉛半田を使用していてもレッドフリーマークがプリントされていないものがあります）：レッドフリーマーク無鉛半田には，以下の特性があります。・融点が従来の半田よりも約40℃高い。従来の半田こてをそのまま使用することは可能ですが，少し長めにこてを当てる必要があります。温度調節機能のついた半田こてを使用する場合，約350℃に設定して下さい。注意：半田こてを長く当てすぎると，基板のパターン（銅箔）がはがれてしまうことがありますので，注意して下さい。・粘性が強い従来の半田よりも粘性が強いため，IC端子などが半田ブリッジしないように注意して下さい。・従来の半田と混ぜて使用可能無鉛半田には無鉛半田を追加するのが最適ですが，従来の半田を追加しても構いません。

– ENGLISH –

– JAPANESE –

(6)

1. SERVICE NOTE

– ENGLISH –

1-3-3. Self-diagnosis Code Table

Self-diagnosis Code

Symptom/State Correction

Repaired by:

Block

Function DetailedCode

C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.

C 0 6 0 0 The battery pack temperature is high. Change the battery pack or place it in a cool place. C 1 3 0 1 Memory card is unformatted._{Memory card is broken.} Format the memory card._{Insert a new memory card.}

C 1 3 0 2 Disc access error

HDR-CX116E/CX150/CX150E/CX155E DCR-SX73E/ SX83/SX83E

Remove the power source. Reconnect it again and operate your camcorder again.

E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note)

E 6 1 0 0 Difficult to adjust focus_{(Cannot initialize focus)}

In case zooming is performed by the touch panel operation, inspect the focus reset sensor (pin qf, wa to wf of CN1003 on the VC-590 board).

In case zooming is not performed, inspect the focus motor drive circuit (IC5306 on the VC-590 board).

E 6 1 1 0 Zoom operations fault_{(Cannot initialize zoom lens.)}

Inspect the lens block zoom MR sensor (pin 1 to 4 , qk of CN1003 on the VC-590 board) when zooming is performed when the zoom lever is operated, or the zoom motor drive circuit (IC5306 on the VC-590 board) when zooming is not performed.

E 6 1 1 1

The abnormalities in initialization of the focus lens and the abnormalities in initialization of the zoom lens oc-curred simultaneously.

Check both C: 61: 00 and E: 61: 10 of the self-diagnosis code.

E 6 2 0 0 Handshake correction function does not work well. (With PITCH angular velocity sensor output stopped.)

Inspect PITCH angular velocity sensors (SE6602 on the MS-431 board) peripheral circuits.

E 6 2 0 1 Handshake correction function does not work well. (With YAW angular velocity sensor output stopped.)

Inspect YAW angular velocity sensors (SE6603 on the MS-431 board) peripheral circuits.

E 9 2 0 1 Battery current value goes over the _{max discharge current}

Check the remaining battery power because this symptom maybe depended on the remaining battery level, and confirm whether or not the symptom is occurred after replacing the battery.

If the symptom is still occurred, overhaul inspection is needed.

Connect MS-431 board to VC-590 board via FP-1185 (MS) flexible board and connect DC/BATT harness to VC-590 board (this is the minimum connection to periphery). in the above state, check each output of DC/DC converter (IC4701).

E 9 4 0 0 Fault of writing or erasing the flash _memory Inspect the flash memory (IC8101 on the VC-590 board). E 9 4 0 1 Internal flash memory fault EXCEPT HDR-CX110/110E/CX115E_{Inspect the flash memory (IC8701 on the JK-395 board).} E 9 4 0 2 BGM data error Inspect the flash memory (IC8701 on the JK-395 board). If it _{is OK, check the CPU (IC7501 on the VC-590 board).}

Note: Start the Adjust Manual in the Adjust Station and refer to the “Destination data write”.

1-1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate.

These following method is available to prevent this.

Method:

Use the genuine AC power adaptor

1-2. PRECAUTION ON REPLACING THE VC-590 BOARD

Turn on the set and establish a USB connection , save the USB serial data before replacing the board.

DESTINATION DATA

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.

After the board replacement, the error of the built-in recording media may be displayed. in this case, execute the [DESTINATION DATA WRITE] then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.

USB SERIAL SAVE

When you replace to the repairing board, get the data from the former one.

Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.

USB SERIAL No.

The set is shipped with a unique ID (USB Serial No.) written in it.

This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.

1-3. SELF-DIAGNOSIS FUNCTION

1-3-1. Self-diagnosis Function

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual.

1-3-2. Self-diagnosis Display

When problems occur while the unit is operating, the counter of the LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.

1 1

3 1

C

Repaired by:

Refer to “1-3-3. Self-diagnosis Code Table” . Indicates the appropriate

step to be taken. E.g.

31 ....Reload the tape. 32 ....Turn on power again.

Block Detailed Code

Blinks at 3.2Hz C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer LCD screen C : 3 1 : 1 1

(7)

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

1-2E

1-1. 修理時の電源供給について

本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。これを避けるため，下記の方法を用いてください。

方法：

ACアダプタを使用する。基板を交換した後，内蔵メモリーのエラーがディスプレイに表示される事があります。この場合は，[DESTINATION DATA WRITE] を実行することでエラーが解消されます。エラーが解消されない場合は，[DESTINATION DATA WRITE] と共に内蔵メモリーをフォーマットしてください。

1-2. VC-590基板交換時の注意

基板交換時は下記の仕向書き込みとUSB SERIAL SAVEが必要です。

仕向けデータ

補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 Adjust StationからAdjust Manualを起動させて「Destination data write」を実行させてください。

USBシリアルセーブ

補修用基板と交換する時，交換前の基板よりUSBシリアルNo.を取得してください。データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。

USBシリアルNo.

セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。 Adjust StationからAdjust Manualを起動させて「USB serial No. input」を実行させてください。

1-3. 自己診断機能

1-3-1. 自己診断機能について

本機の動作に不具合が生じたとき，自己診断機能が働き，ビューファインダまたはLCD画面に，どう処置したらよいか判断できる表示を行います。「自己診断表示」と「サービスモード表示」の２つの表示があります。自己診断機能については取扱説明書にも掲載されています。

1-3-2. 自己診断表示

本機の動作に不具合が生じたとき，LCD画面のカウンタ表示部分がアルファベットと数字の4桁表示になり，3.2Hzで点滅します。この5 文字の表示によって対応者分類および不具合の生じたブロックの分類，不具合の詳細コードを示します。

1-3-3. 自己診断コード表

シート”自己診断表（J)”より表を挿入

1 1

C

3

1

対応者分類「1-3-3.自己診断コード表」を参照対応方法の違いにより分類例 31･･･テープを入れ直す 32･･･電源を入れ直すブロック分類詳細コード 3.2Hz点滅 C：お客さま自身で対応 H：販売店で対応 E：サービスエンジニアで対応 LCD画面 C : 3 1 : 1 1

1 1

C

3

1

対応者分類「1-3-3.自己診断コード表」を参照対応方法の違いにより分類例 31･･･テープを入れ直す 32･･･電源を入れ直すブロック分類詳細コード 3.2Hz点滅 C：お客さま自身で対応 H：販売店で対応 E：サービスエンジニアで対応 LCD画面 C : 3 1 : 1 1

– JAPANESE –

1-3-3. 自己診断コード表

自己診断コード症状／状態対応／方法対応者ブロック機能コード詳細 C 0 4 0 0 標準でないバッテリを使用しているインフォリチウムバッテリを使用する。 C 0 6 0 0 バッテリが高温になっているバッテリを交換するか、バッテリを涼しいところに置_く。 C 1 3 0 1 フォーマットしていないメモリーカードを入れたメモリーカードが壊れているメモリーカードをフォーマットする。新しいメモリーカードに交換する。 C 1 3 0 2 アクセスエラー電源を外し，再度入れ直してから操作する。 E 2 0 0 0 フラッシュメモリが書き換えられて_いるフラッシュメモリのデータを元の値に戻す。（注意） E 6 1 0 0 _{（フォーカスの初期化ができない）}フォーカスが合いにくいタッチパネルでフォーカス操作をしたときにフォーカス動作をすれば，レンズブロックのフォーカスリセットセンサ（VC-590基板CN1003 qf, wa ～ wfピン）を点検する。フォーカス動作をしなければフォーカスモータ駆動回路（VC-590基板IC5306）を点検する。 E 6 1 1 0 ズーム動作の異常（ズームレンズの_{初期化ができない）} ズームレバーを操作したときにズーム動作をすれば，レンズブロックのズームMRセンサ（VC-590基板 CN1003 1 ～ 4, qkピン）を点検する。ズーム動作をしなければズームモータ駆動回路（VC-590基板IC5306）を点検する。 E 6 1 1 1 フォーカスレンズ初期化異常，ズー_{ムレンズ初期化異常の同時発生} 自己診断コードC：32：60とE：61：10の両方を点検_する。 E 6 2 0 0 _{（PITCH角速度センサ出力張り付き）}手振れ補正が効きにくい PITCH角速度センサ（MS-431基板SE6602）周辺回路を_点検。 E 6 2 0 1 _{（YAW角速度センサ出力張り付き）}手振れ補正が効きにくい YAW角速度センサ（MS-431基板SE6603）周辺回路を点_検。 E 9 2 0 1 (バッテリーの)電流値が最大放電電_{流を超えた} バッテリ残量に依存する場合があるので，バッテリ残量を確認する。次にバッテリを交換して症状が出るか確認する。バッテリを交換しても症状が出る場合は，エラー発生後に電源が切れてしまうため，分解して確認する， VC-590基板にMS-431基板をFP-1185 (VC-MS) フレキシブル基板で接続し，DC/バッテリハーネスをVC-590 基板に接続した状態 (最小限の接続) でDC ／ DCコンバータ (VC-590基板IC4701) の各チャンネル出力を確認する。 E 9 4 0 0 フラッシュメモリの書込み/消去動_作不良フラッシュメモリ（VC-590基板 IC8101）を点検する。 E 9 4 0 1 フラッシュメモリ内部異常フラッシュメモリ（JK-395基板 IC8701）を点検する。 E 9 4 0 2 BGM データ異常フラッシュメモリ（JK-395基板 IC8701）を点検する。異常がない場合は，CPU（VC-590基板 IC7501）を点検する。 注意： Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を参照してください。

(8)

2. REPAIR PARTS LIST

Follow the disassembly in the numerical order given.

IDENTIFYING PARTS

AC-

DIS-Link

ACCESSORIES ASSEMBLY

VC-590

4 BT Panel Section [Disassembly] [Exploded View] • MS-431 Board • FP-1189 Flexible Board 6 Cabinet (R) Section [Disassembly] [Exploded View] • LCD Section • PD-404 Board • Cabinet (R) Section • JK-395 Board • FP-1183 Flexible Board • FP-1191 Flexible Board • FP-1192 Flexible Board (CX116E/CX150/CX150E/CX155E/ CX170/SX73E/SX83/SX83E) 8 Lens Section • CM-114 Board 1 Cabinet (L) Section 5 Cabinet (F) Section 2 Cabinet BM Block 7 VC-590 Board 3 Cabinet T Section

(ENGLISH)

NOTE:

• -XX, -X mean standardized parts, so they may have some differences from the original one.

• Items marked “*” are not stocked since they are seldom re-quired for routine service. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not supplied.

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

(JAPANESE)

【使用上の注意】 • ここに記載されている部品は，補修用部品であるため，回路図及びセットに付いている部品と異なる場合があります。 • -XX，-Xは標準化部品のため，セットに付いている部品と異なる場合があります。 • *印の部品は常備在庫しておりません。

• Color Indication of Appearance Parts Example:

(SILVER) : Cabinet’s Color (Silver) : Parts Color

• 外装部品色表示例：

(SILVER) ：セットの色を表す。 (Silver) ：部品の色を表す。

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

0印の部品，または0印付の点線で囲まれた部品は，

安全性を維持するために，重要な部品です。

従って交換時は，必ず指定の部品を使用してください。

• Abbreviation

AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model KR : Korea model NE : North European model

Right View Left View Front View Bottom View Top View Back View

View Position

(9)

2-2

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of con-nector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt which comes off at the point. (Be careful or some

pieces of gilt may be left inside)

修理時の注意

• フラットケーブルおよびフレキシブル基板の端子面に欠け，折れ等がないことを確認する。また，コネクタへの接続は，差し込み不足や斜め差しにならないように注意する。 • コネクタを取り外す時に，線材部（極細）を持って引っ張ると断線する恐れがありますので，絶対に線材部（極細）を持って引っ張らないでください。 • 線材部（極細）を押さえながらコネクタを差し込むと，線材部（極細）が断線する恐れがありますので，絶対に線材部（極細）には負担をかけないでください。 • 金メッキされているフレキシブル基板には，強い負担をかけないでください。先端の剥がれたメッキ部はカットして除去してください。（メッキ破片がコネクタ内に残っている場合もあるので注意してください）

– ENGLISH –

– JAPANESE –

(10)

2-1. EXPLODED VIEWS

2-1-1. OVERALL SECTION

ns: not supplied

Ref. No. Part No. Description Ref. No. Part No. Description 1 A-1757-261-A CABINET L (337B) ASSY (BLACK)

1 A-1757-262-A CABINET L (337L) ASSY (BLUE(EXCEPT CX150: US)) 1 A-1757-263-A CABINET L (337R) ASSY (RED) 1 A-1757-264-A CABINET L (335S) ASSY (SILVER) 1 A-1762-317-A CABINET L (338LI) ASSY (BLUE(CX150: US)) 2 4-166-606-01 BELT, GRIP (10) (SILVER)

2 4-166-606-11 BELT, GRIP (10) (BLUE(EXCEPT CX150: US)) 2 4-166-606-21 BELT, GRIP (10) (RED)

2 4-166-606-31 BELT, GRIP (10) (BLACK/BLUE(CX150: US)) 3 4-177-121-01 GASKET (L (337)) * 4 4-171-813-01 TRIPOD RETAINER 5 3-283-643-01 SCREW, TRIPOD 6 4-171-812-01 CABINET BM #2 2-635-562-31 SCREW (M1.7) #11 3-078-890-11 SCREW, TAPPING #12 3-080-204-21 SCREW, TAPPING, P2

1. Remove to numerical order (

1

to

2

) in the left figure.

DISASSEMBLY

1 _{#12 X 1 → #2 X 5}

2 _{#2 X 3}

Bottom View

#2

Left View Right View

Back View Bottom View #12 _#2 _#2 #2 #2 #11

1 ₁

2 ₆

3

2

4

5

#2 #2 #2 ns ns ns Top/Front Section (See page 2-4) #2 #12 #2 #2

Screw

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 4.0 1.7 #12: M1.7 X 5.0 (Tapping) (Black) 3-080-204-21 1.7 5.0

(11)

2-

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

2-1-2. TOP/FRONT SECTION

ns: not supplied

Ref. No. Part No. Description Ref. No. Part No. Description 51 A-1757-196-A CABINET F (337B) ASSY (BLACK)

51 A-1757-197-A CABINET F (337L) ASSY (BLUE(EXCEPT CX150: US)) 51 A-1757-198-A CABINET F (337R) ASSY (RED) 51 A-1757-199-A CABINET F (335S) ASSY (SILVER) 51 A-1762-320-A CABINET F (338LI) ASSY (BLUE(CX150: US)) * 52 A-1757-195-A RETAINER ASSY, MICROPHONE

* 53 4-172-027-01 HEAT SINK BM (337)

54 A-1757-250-A CABINET T BLOCK ASSY (BLACK) 54 A-1757-256-A CABINET (T) BLOCK ASSY (RED) 54 A-1757-257-A CABINET (T) BLOCK ASSY (BLUE(EXCEPT CX150: US))

54 A-1757-258-A CABINET (T) BLOCK ASSY (SILVER) 54 A-1762-323-A CABINET (T) BLOCK ASSY (BLUE(CX150: US)) 55 1-487-575-11 SWITCH BLOCK, CONTROL (PS33700) * 56 4-171-734-01 TOP FRAME

MIC901 1-542-821-11 MICROPHONE UNIT #2 2-635-562-31 SCREW (M1.7) #11 3-078-890-11 SCREW, TAPPING #12 3-080-204-21 SCREW, TAPPING, P2

3

to

5

2. The meaning of the sign in left figure is as follows. Be careful when it removes.

◆-X: Flexible Board, Flat Cable, Harness

DISASSEMBLY

3 _{#2 X 5}

4 #2 X 1 → Heat Sink BM (337) (

4 _{) → #2 X 6}

Top View

#2

#2 #2

Back View #2

#2 #2

5 #2 X 1

Top View #2 #11 MIC901 #2 #2 #2 #2 #2 #12 ns ns ns #2 #12 #2 #2 #2 #2 Main Section (See page 2-5)

5 ₅₁

53

4

3 ₅₄

56

52

55

4

BT Panel Section (See page 2-8)

-5

-4

(Boss)

Screw

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 4.0 1.7 #12: M1.7 X 5.0 (Tapping) (Black) 3-080-204-21 1.7 5.0

(12)

Ref. No. Part No. Description Ref. No. Part No. Description * 101 4-172-026-01 HEAT SINK VC

102 4-177-120-01 SHEET (VC), SHIELD

* 103 4-165-732-01 LABEL, FUSE REPLACEMENT CAUTION 104 4-174-979-01 SHEET (AN), RADIATION (CX110/CX110E/CX115E/ CX116E/CX150/CX150E/CX155E/CX170) * 105 4-172-028-01 SHEET VC, RADIATION

106 A-1757-118-A VC-590 BOARD, COMPLETE (SERVICE) (CX110/CX110E/CX150/CX150E/CX170)(Note 2) 106 A-1757-119-A VC-590 BOARD, COMPLETE (SERVICE) (SX83/SX83E)(Note 2)

106 A-1757-122-A VC-590 BOARD, COMPLETE (SERVICE) (CX115E/CX116E/CX155E)(Note 2) 106 A-1757-123-A VC-590 BOARD, COMPLETE (SERVICE)

(SX73E)(Note 2)

107 1-880-345-11 FP-1185 FLEXIBLE BOARD

108 8-848-865-01 DEVICE, LENS LSV-1181A * 109 4-172-024-01 MAIN FRAME

110 1-856-061-21 OPTICAL FILTERBLOCK (OFB-06-12) 111 4-163-258-01 RUBBER (1181), SEAL

112 A-1756-539-A CM-114 BOARD, COMPLETE (including CP002 (CMOS imager)) (Note 1)

113 1-880-344-11 FP-1184 FLEXIBLE BOARD 114 4-172-039-01 SHEET (CM), SHIELD 115 4-172-029-01 SHEET CM, RADIATION (Note 3) * 116 4-172-025-01 HEAT SINK LE

117 4-182-848-01 INSULATING SHEET (LE) 118 4-177-119-01 SHEET (MF), SHIELD #2 2-635-562-31 SCREW (M1.7)

#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 #11 3-078-890-11 SCREW, TAPPING

#172 2-178-410-01 TITE (UB TITE) 1.4

2-1-3. MAIN SECTION

6

to

8 DISASSEMBLY

6 _{#3 X 1 → #2 X 1}

Screw

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7

Top View Right View

#3 #2

Note

#3: M1.7 X 2.5 (Red) 2-660-401-01 2.5 1.7 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 4.0 1.7 #172: M1.4 X 4.0 (Tapping) (Black) 2-178-410-01 1.4 4.0 CX110/CX110E/CX115E/ CX116E/CX150/CX150E /CX155E/CX170 A B C A C B #2 #3 #11 #3 #3 #3 #3 #172

8 ₁₀₈

VC-590

102

6

LCD Section (See page 2-6)

103

104

105

107

111

113

118

105

117

110

114

109 8-2

116 8-1

7 ₁₀₆

(Note 2)

115 7-1

(Note 3)

101 7-2

112

(including CP002 (CMOS imager)) (Note 1)

7 _{Radiation Sheet CM (}

7 _-1

_{) → #3 X 2 → Heat Sink VC (}

7 _-2

_{) → #3 X 1}

Bottom View

#3

Note 1: Be sure to read “Precautions for Replacement of Imager”

on page 6-1 when changing the imager. Note 1: イメージャの交換時は6-1ページの“イメージャ交換時の注意”を必ずお読みください。

Note 2: When replacing the VC-590 board, start the Adjust

Manual in the Adjust Station and refer to the “INTERNAL MEMORY ADJUSTMENTS”.

Note 2: VC-590基板を交換の際は，Adjust Stationから

Adjust Manualを起動させて「INTERNAL MEMORY ADJUSTMENTS」を参照してください。

Note 3: The Radiation Sheet CM when peeling off once, so that

it cannot be reused. Note 3: Radiation Sheet CMは一度剥がすと粘着力が弱くなるため、再利用はしないでください。

8 _{#3 X 1 → Heat Sink LE (}

8 _-1

_{) → #11 X 2 → Main Frame (}

8 _-2

₎

Bottom View Left View

(13)

2-6

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

2-1-4. LCD SECTION

ns: not supplied

Ref. No. Part No. Description Ref. No. Part No. Description 151 A-1757-226-A CABINET P (B) 3370 ASSY

(CX110(BLACK)/CX110E(BLACK)) 151 A-1757-227-A CABINET P (R) 3370 ASSY (CX110(RED)/CX110E(RED)) 151 A-1757-228-A CABINET P (L) 3370 ASSY (CX110(BLUE)/CX110E(BLUE)) 151 A-1757-229-A CABINET P (S) 3350 ASSY (SX83/SX83E) 151 A-1757-230-A CABINET P (S) 3380 ASSY (CX150E(SILVER)) 151 A-1757-231-A CABINET P (B) 3380 ASSY (CX150(BLACK)/

CX150E(BLACK))

151 A-1757-234-A CABINET P (R) 3380 ASSY (CX150(RED)/

CX150E(RED))

151 A-1757-236-A CABINET P (L) 3380 ASSY (CX150(BLUE): KR/

CX150E(BLUE))

151 A-1757-237-A CABINET P (B) 3365 ASSY (CX115E(BLACK)) 151 A-1757-238-A CABINET P (R) 3365 ASSY (CX115E(RED)) 151 A-1757-239-A CABINET P (L) 3365 ASSY (CX115E(BLUE)) 151 A-1757-240-A CABINET P (B) 3375 ASSY (CX155E) 151 A-1757-241-A CABINET P (S) 3345 ASSY (SX73E) 151 A-1757-243-A CABINET P (B) 3367 ASSY (CX116E) 151 A-1762-318-A CABINET P (LI) 3380 ASSY (CX150(BLUE): US)

151 A-1762-394-A CABINET P (B) 3390 ASSY (CX170(BLACK)) 151 A-1762-395-A CABINET P (R) 3390 ASSY (CX170(RED)) 151 A-1762-396-A CABINET P (L) 3390 ASSY (CX170(BLUE)) 151 A-1762-397-A CABINET P (S) 3390 ASSY (CX170(SILVER)) 152 A-1751-597-A PD-404 BOARD, COMPLETE

153 4-171-973-01 LCD RETAINER 154 4-171-972-01 LCD CUSHION * 155 4-171-971-01 PLATE P, GROUND 156 4-171-970-01 CABINET (M), P (BLACK) 156 4-171-970-11 CABINET (M), P (RED)

156 4-171-970-21 CABINET (M), P (BLUE(EXCEPT CX150: US)) 156 4-171-970-31 CABINET (M), P (SILVER)

156 4-171-970-41 CABINET (M), P (BLUE(CX150: US)) * 157 4-171-975-01 FPC CLAMPER (Note)

LCD901 1-811-015-11 LCD MODULE WITH TOUCH PANEL (EXCEPT SX73E/SX83/SX83E)

LCD901 A-1748-996-A FTS BLOCK ASSY 27STMG10 (SX73E/SX83/

SX83E) #2 2-635-562-31 SCREW (M1.7) #11 3-078-890-11 SCREW, TAPPING

Screw

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 4.0 1.7 PD-404 #11 #11 ns #2 #11 LCD901

151

152

157

(Note)

153

154

155

156

(Claw) (Claw) (Claw) Cabinet (R) Section (See page 2-7)

Note

Note: Refer to “Assembly-2: Installation Caution of the FPC

(14)

2-1-5. CABINET (R) SECTION

ns: not supplied

Ref. No. Part No. Description Ref. No. Part No. Description 201 A-1757-179-A CABINET (R (337B)) ASSY (BRACK)

201 A-1757-180-A CABINET (R (337L)) ASSY (BLUE(EXCEPT CX150: US)) 201 A-1757-181-A CABINET (R (337R)) ASSY (RED) 201 A-1757-182-A CABINET (R (335S)) ASSY (SILVER(SX73E/SX83/SX83E))

201 A-1757-183-A CABINET (R (338S)) ASSY (SILVER (CX150E: CH/

CX170))

201 A-1762-411-A CABINET R (338LI) ASSY (BLUE(CX150: US)) * 202 4-171-758-01 JK LID R (EXCEPT SX73E/SX83/SX83E) 203 A-1756-550-A JK-395 BOARD, COMPLETE (CX110/CX110E/CX115E) 203 A-1756-548-A JK-395 BOARD, COMPLETE (CX150/CX150E/CX155E)

203 A-1756-549-A JK-395 BOARD, COMPLETE (SX73E/SX83/SX83E) 203 A-1756-550-A JK-395 BOARD, COMPLETE (CX116E)

203 A-1761-893-A JK-395 BOARD, COMPLETE (CX170) 204 1-880-352-11 FP-1192 FLEXIBLE BOARD (CX116E/CX150/ CX150E/CX155E/CX170/SX73E/SX83/SX83E) * 205 4-171-760-01 JK RETAINER R

* 206 4-171-759-01 JK FRAME

207 1-880-351-11 FP-1191 FLEXIBLE BOARD (Note 2) * 208 4-171-660-01 HINGE COVER U

209 1-471-504-11 MAGNET (ND5X3.5X2.4-B) * 210 4-171-761-01 BLIND, HINGE

211 X-2546-139-1 HINGE M (1) ASSY, 10 STYLE 212 CAUTION SHEET, ADHESIVE, HINGE 213 1-880-343-11 FP-1183 FLEXIBLE BOARD (Note 1) * 214 4-171-661-01 HINGE COVER O (BLACK) * 214 4-171-661-11 HINGE COVER O (RED)

* 214 4-171-661-21 HINGE COVER O (BLUE(EXCEPT CX150: US)) * 214 4-171-661-31 HINGE COVER O (SILVER)

* 214 4-171-661-41 HINGE COVER O (BLUE(CX150: US)) SP901 1-858-310-51 SPEAKER (1.3CM)

#1 2-635-562-11 SCREW (M1.7) #2 2-635-562-31 SCREW (M1.7)

#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 #12 3-080-204-21 SCREW, TAPPING, P2 CX116E/CX150/CX150E/ CX155E/CX170/SX73E/ SX83/SX83E

212

(38mm × 33mm)

201

202

#12 #1 #3 #2 SP901 #12 ns ns

203

204

206

207

(Note 2)

205

208

211

209

210

213

(Note 1)

214

#12

Screw

#1: M1.7 X 2.5 (Black) 2-635-562-11 2.5 1.7

Note

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7 #3: M1.7 X 2.5 (Red) 2-660-401-01 2.5 1.7 #12: M1.7 X 5.0 (Tapping) (Black) 3-080-204-21 1.7 5.0

Note 1: Refer to “Assembly-1: The method of attachment of

FP-1189 Flexible Board”. Note 1: “Assembly-1: The method of attachment of FP-1189 Flexible board"を参照してください。

Note 2: Refer to “Assembly-3: Installation Caution of the FP-1192

Flexible Board”. Note 2: “Assembly-3: Installation Caution of the FP-1192 Flexible Board"を参照してください。

Caution :

For the part of 212 : SHEET, ADHESIVE, HINGE (3-089-65-01), cut SHEET, ADHESIVE (2-69-300-01) into the desired length and use it.

注意 :

212 : SHEET, ADHESIVE, HINGE (3-089-465-01)は、SHEET, ADHESIVE (2-649-300-01) を切って使用してください。

(15)

2-8

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

Ref. No. Part No. Description Ref. No. Part No. Description 251 4-177-123-01 SHEET (MS), SHIELD

252 A-1756-546-A MS-431 BOARD, COMPLETE 253 A-1757-283-A SLOT ASSY, MS

* 254 4-171-818-01 BT RETAINER CLAW * 255 4-171-820-01 BT FRAME * 256 4-172-031-01 JK RETAINER L (337)

257 A-1756-534-A FP-1189 FLEXIBLE BOARD, COMPLETE (Note 2) 258 4-172-030-01 JK HOLDER L (337)

259 4-177-124-01 DC, SHIELD SHEET * 260 4-171-819-01 HEAT SINK, BT

* 261 4-171-817-01 BT PANEL

0 262 1-822-470-31 JACK, DC (including BT901 and J901) (Note 2) 0 BH7301 1-756-615-61 HOLDER, BATTERY (Note 1)

0 BT7301 1-756-134-12 LITHIUM ION BATTERY (Note 1) #2 2-635-562-31 SCREW (M1.7)

#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 #11 3-078-890-11 SCREW, TAPPING

2-1-6. BT PANEL SECTION

ns: not supplied

MS-431

#11 #2 #3 #2

262

(including BT901 and J901) (Note 2)

253

254

255

BT7301 (Note 1) BH7301 (Note 1) ns

252

251

258

257

(Note 2)

256

259

260

261

: BT7301 (LITHIUM ION BATTERY) Board on the mount position. (See page 6-26 of LEVEL 3)

Screw

#2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7

Note

#3: M1.7 X 2.5 (Red) 2-660-401-01 2.5 1.7 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 4.0 1.7

Note 1: Note Replace the battery holder (BH7301) together when replacing the lithium storage battery (BT7301) on the MS-31 board.

(The battery holder removed once cannot be used again.)When mounting these parts, mount new battery holder first and attach new lithium storage battery next.

Note 1: MS-431基板のリチウム蓄電池 (BT7301) を交換する場合 はバッテリホルダ (BH7301) も同時に新品に交換してください。 (一度使用したバッテリホルダは再使用できません。) 部品取り付けの際は、先にバッテリホルダを取り付けてからリチウム蓄電池を装着してください。

Note 2: Refer to “Assembly-: Installation Cautions of the DC

Jack Harness and the FP-1189 Flexible Board”. Note 2: “Assembly-4: Installation Cautions of the DC Jack Harness _{and the FP-1189 Flexible Board"を参照してください。}

Caution :

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.

注意 :

電池の交換は、正しく行わないと破裂する恐れがあります。電池を交換する場合には必ず同じ型名の電池又は同等品と交換してください。

(16)

• EXCEPT J MODEL

Checking supplied accessories.

Conversion (2P) Adaptor 0 1-56-007-12 (E:NTSC ,JE) AC Adaptor (AC-L200C/L200D) (EXCEPT BR) * Compatible in L200C and L200D 0 1-487-150-51

Power cord (Mains lead) (EXCEPT BR) 0 1-832-121-41 (CH) 0 1-832-16-41 (UK, HK) 0 1-833-82-41 (KR)

0 1-834-482-21 (AEP, NE, E:PAL) 0 1-834-484-31 (US, CND) 0 1-834-852-11 (E:NTSC) 0 1-835-83-11 (AUS) 0 1-836-251-11 (JE)

A/V connecting cable 1-823-156-61

USB cable 1-835-3-31

Rechargeable battery pack (NP-FV30) SX73E/SX83/SX83E 0 A-1738-740-A (US) 0 A-1738-741-A (EXCEPT US, CH) 0 A-1738-742-A (CH) * * * * * * * * * * * * Operating Guide CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E 4-170-86-11 (ENGLISH, SPANISH) 4-170-86-21 (FRENCH) 4-170-86-31 (PORTUGUESE) 4-170-86-41 (TRADITIONAL CHINESE) 4-170-86-51 (KOREAN) 4-170-87-11 (ENGLISH)

4-170-87-21 (FRENCH, DUTCH, GERMAN, ITALIAN) 4-170-87-31 (SPANISH, PORTUGUESE, GREEK, TURKISH) 4-170-87-41 (POLISH, CZECH, HUNGARIAN, SLOVAK) 4-170-87-51 (DANISH, FINNISH, SWEDISH, ROMANIAN) 4-170-87-61 (RUSSIAN, UKRAINIAN)

4-170-87-71 (TRADITIONAL CHINESE) 4-170-87-81 (SIMPLIFIED CHINESE) (E: PAL (EXCEPT Middle East), JE) 4-170-87-1 (ARABIC, PERSIAN) 4-170-8-11 (SIMPLIFIED CHINESE) (CH) 4-170-8-21 (RUSSIAN, UKRAINIAN) (CH) * * * * * * * * * Operating Guide SX73E/SX83/SX83E 4-171-513-11 (ENGLISH, SPANISH) 4-171-513-51 (KOREAN) 4-171-514-11 (ENGLISH)

4-171-514-21 (FRENCH, DUTCH, GERMAN, ITALIAN) 4-171-514-31 (SPANISH, PORTUGUESE, GREEK, TURKISH) 4-171-514-41 (POLISH, CZECH, HUNGARIAN, SLOVAK) 4-171-514-51 (DANISH, FINNISH, SWEDISH, ROMANIAN) 4-171-514-61 (RUSSIAN, UKRAINIAN)

4-171-514-81 (SIMPLIFIED CHINESE) (E: PAL (EXCEPT Middle East)) 4-171-514-1 (ARABIC, PERSIAN)

4-171-516-11 (SIMPLIFIED CHINESE) (CH)

Component A/V cable 1-834-646-11

Rechargeable battery pack

CX110/CX110E/CX115E/CX116E/ CX150/CX150E/CX155E

(NP-FV50) (Note)

Note : This item is supplied with the unit as an accessory, but is not prepared as a service part.

(Only for destination Japanese model)

日本語・英語・韓国語・中国語のみ部品供給可能です。 (Only for destination Japanese model)日本語・英語・韓国語・中国語のみ部品供給可能です。

* * * * * * * * * * * * * * * * * * * * * * CD-ROM "Handycam Application Software" - "PMB" (software) including "PMB Guide" - "Handycam Handbook" (PDF) CX110/CX110E/CX115E/ CX116E/CX150/CX150E/ CX155E 4-170-80-01 SX73E/SX83/SX83E 4-171-508-01 Handycam Handbook (PDF) SX73E/SX83/SX83E 4-171-50-11 (ENGLISH) 4-171-50-31 (SPANISH) 4-171-50-61 (KOREAN) 4-171-510-11 (ENGLISH) 4-171-510-21 (FRENCH) 4-171-510-31 (GERMAN) 4-171-510-41 (ITALIAN) 4-171-510-51 (DUTCH) 4-171-510-61 (SPANISH) 4-171-510-71 (PORTUGUESE) 4-171-510-81 (TRUKISH) * * * * * * * * * * * 4-171-510-1 (GREEK) 4-171-511-11 (CZECH) 4-171-511-21 (HUNGARIAN) 4-171-511-31 (SLOVAK) 4-171-511-41 (POLISH) 4-171-511-51 (SWEDISH) 4-171-511-61 (DANISH) 4-171-511-71 (FINNISH) 4-171-511-81 (ROMANIAN) 4-171-511-1 (RUSSIAN) 4-171-512-11 (UKRAINIAN) * * * * * * 4-171-512-31 (SIMPLIFIED CHINESE) 4-171-512-41 (ARABIC) 4-171-512-51 (PERSIAN) 4-171-512-61 (MALAY) 4-171-512-71 (INDONESIAN) 4-171-512-81 (THAI) The CD-ROM supplied contains all of language version of

the Instruction Manual in pdf (Handycam Handbook.pdf) for printing. The printed matter is not supplied. If required,

please order it with the part number below.

4-170-82-11 (ENGLISH) 4-170-82-21 (FRENCH) 4-170-82-31 (SPANISH) 4-170-82-41 (PORTUGUESE) 4-170-82-51 (TRADITIONAL CHINESE) 4-170-82-61 (KOREAN) 4-170-83-11 (ENGLISH) 4-170-83-21 (FRENCH) 4-170-83-31 (GERMAN) 4-170-83-41 (ITALIAN) 4-170-83-51 (DUTCH) * * * * * * * * * * * 4-170-83-61 (SPANISH) 4-170-83-71 (PORTUGUESE) 4-170-83-81 (TRUKISH) 4-170-83-1 (GREEK) 4-170-84-11 (CZECH) 4-170-84-21 (HUNGARIAN) 4-170-84-31 (SLOVAK) 4-170-84-41 (POLISH) 4-170-84-51 (SWEDISH) 4-170-84-61 (DANISH) 4-170-84-71 (FINNISH) * * * * * * * * * * 4-170-84-81 (ROMANIAN) 4-170-84-1 (RUSSIAN) 4-170-85-11 (UKRAINIAN) 4-170-85-21 (TRADITIONAL CHINESE) 4-170-85-31 (SIMPLIFIED CHINESE) 4-170-85-41 (ARABIC) 4-170-85-51 (PERSIAN) 4-170-85-61 (MALAY) 4-170-85-71 (INDONESIAN) 4-170-85-81 (THAI) CX110/CX110E/CX115E/CX116E/ CX150/CX150E/CX155E

(Only for destination Japanese model)

日本国内については印刷での部品供給は行っておりません。

• J MODEL

付属品

ACアダプター (AC-L200C/L200D) * L200CとL200Dには互換性があります。 0 1-487-150-51 A/V接続ケーブル 1-823-156-61 USBケーブル1-82-868-31 CD-ROM「Handycam Application Software」 -「PMB」(ソフトウェア。「PMB ガイド」を含む) -「ハンディカムハンドブック」(PDF) (Note2) 4-170-80-01 電源コード 0 1-836-251-11 リチャージャブルバッテリーパック_(NP-FV50) (Note1) 取扱説明書 4-170-86-01 (日本語) Note1 : 当商品はアクセサリーとして同梱されておりますがサービス用補修部品としては準備しておりません。 D端子A/Vケーブル 1-834-646-21 Note2: 日本国内については印刷での部品供給は行っておりません。

(17)

2-10E

Ref. No. Part No. Description

DCR-SX73E/SX83/SX83E, HDR-CX110/CX110E/CX115E/CX116E/CX150/CX150E/CX155E/CX170_L2

2-2. ELECTRICAL PARTS LIST

1-880-343-11 FP-1183 FLEXIBLE BOARD ******************** 1-880-344-11 FP-1184 FLEXIBLE BOARD ******************** 1-880-345-11 FP-1185 FLEXIBLE BOARD ********************

A-1756-534-A FP-1189 BOARD, COMPLETE *********************** < CONNECTOR > CN1101 1-815-794-13 CONNECTOR (MULTIPLE) 1-880-351-11 FP-1191 FLEXIBLE BOARD ******************** 1-880-352-11 FP-1192 FLEXIBLE BOARD (EXCEPT CX110/CX110E/CX115E) *************************

A-1751-597-A PD-404 BOARD, COMPLETE ********************** (SE6401 is not supplied, but this is included in PD-404 complete board.) < CAPACITOR >

C6401 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C6402 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V * C6403 1-114-582-11 CERAMIC CHIP 0.1uF 10% 16V C6404 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V * C6405 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V C6406 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C6408 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C6409 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V C6410 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V C6411 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V C6412 1-125-889-11 CERAMIC CHIP 2.2uF 10% 10V C6414 1-100-591-91 CERAMIC CHIP 1uF 10% 25V C6415 1-125-889-11 CERAMIC CHIP 2.2uF 10% 10V * C6416 1-112-298-91 CERAMIC CHIP 1uF 10% 16V * C6417 1-112-298-91 CERAMIC CHIP 1uF 10% 16V < CONNECTOR > CN6401 1-822-378-11 CONNECTOR, FPC (ZIF) 33P * CN6402 1-821-503-11 CONNECTOR, FPC (ZIF) 39P CN6403 1-816-654-61 FFC/FPC CONNECTOR (LIF) 6P < COIL > * L6401 1-481-102-21 INDUCTOR 10uH

FP-1192 PD-404

* L6402 1-481-102-21 INDUCTOR 10uH < TRANSISTOR > * Q6401 6-552-337-01 TRANSISTOR DMG9640N0L * Q6402 6-552-337-01 TRANSISTOR DMG9640N0L < RESISTOR > R6402 1-218-953-11 METAL CHIP 1K 5% 1/16W R6403 1-218-953-11 METAL CHIP 1K 5% 1/16W R6405 1-218-985-11 METAL CHIP 470K 5% 1/16W < AMR SENSOR >

SE6401 (Not supplied) AMR SENSOR

(SE6401 is supplied included in PD-404 complete board.)

FP-1191

FP-1189

FP-1185

FP-1184

FP-1183

CM-114，JK-395，MS-431およびVC-590のELECTRICAL PARTS LISTについては、LEVEL3を参照して下さい。

Please refer to LEVEL 3 about the ELECTRICAL PARTS LIST of CM-11, JK-395, MS-31 and VC-590.

(18)

3. ASSEMBLY

Assembly-1: The Method of attachment of FP-1183

Flexible Board

1 Fold dotted line parts of the FP-1183 flexible

board as shown in figure.

FP-1183 Flexible Board Unite corners. Valley fold Valley fold Mountain fold Adhesive tape Adhesive tape Mountain fold

2 Install the flexible clamp in the hinge assy

as shown in figure.

4 Install the hinge cover O.

3 Install the the magnet to the hinge cover U

with the magnet.

5 Roll the FP-1183 flexible board 2.5 times

in the hinge assy as shown in figure.

2.5 times Hinge Assy Adhesive Part Claws Hinge Cover U Hinge Cover O Magnet

Assembly-2: Installation Caution of the FPC Clamper

The FP-1183 flexible board must be caught by FPC clamper as shown in the figure.

FP-1183 Flexible Board

FPC Clamper

Assembly-3: Installation Caution of the FP-1191

Flexible Board

JK-395 Board

Push the FP-1191 flexible board as shown below.

VC-590 Board FP-1191

Flexible Board

Assembly-4: Installation Cautions of

the DC Jack Harness and

the FP-1189 Flexible Board

Route the FP-1189 flexible board as shown below.

Lib Lib FP-1189 Flexible Board JK Holder L (337) Purple Brown Libs Lib JK Holder L (337) White JK Holder L (337) JK Retainer L (337) Red Black Blue Libs Lib

Route the DC jack harness as shown below.

Route the three harnesses to outside of the connector.

Route the three harnesses to inside of the connector. Libs Red Black Blue Purple Brown White