• 検索結果がありません。

英語版　ZD 5013 テンションコントローラ 駆動機器 ｜三菱電機 FA

N/A
N/A
Info
ダウンロード
Protected

Academic year: 2018

シェア "英語版　ZD 5013 テンションコントローラ 駆動機器 ｜三菱電機 FA"

Copied!
2
0
0

読み込み中.... (全文を見る)

今ダウンロードする ( 2 ページ )

全文

(1)

+($'2)),&(72.<2%8,/',1*0$58128&+,&+,<2'$.872.<2-$3$1 1$*2<$:25.6<$'$0,1$0,&+20(+,*$6+,.81$*2<$-$3$1

TECHNICAL BULLETIN

[ 1/2

]

Thank you for your continued support of Electromagnetic Clutch and Brake, and power supply.

The 80 V DC powder brake/manual power supply have been used over the years since its release. At this time, it is very diffi cult to obtain main parts used in production of the 80 V DC powder brake/manual power supply, and diffi cult to maintain the production system.

We would like to announce that the production of the object models will be ending according to the following schedule.

For the substitute models, please refer to the following.

1. Object models for which production will be discontinued

(1) ZX type powder brake (2) Manual power supply

Model Model code Model Model code

ZX-0.3YN-80 093406 LL-05ZX 094252

ZX-0.6YN-80 093408

ZX-1.2YN-80 093410

2. Time of production discontinuation

- Start to build-to-order system: August 1, 2017

- Time of production discontinuation: September 30, 2018

3. Reason for production discontinuation

The main parts cannot be obtained.

4. Repair acceptance

Repair acceptance period: September 30, 2025 (For 7 years after production is discontinued)

However, please note that we cannot accept requests for repair if replacement parts are no longer available even within the repair acceptance period.

5. Substitute model

(1) ZX type powder brake (2) Manual power supply

Production discontinuation models Substitute model Production discontinuation models Substitute model

Model Model Model code Model Model Model code

ZX-0.3YN-80 ZX-0.3YN-24 093405

LL-05ZX

LD-10PAU-A*1 094049

ZX-0.6YN-80 ZX-0.6YN-24 093407 LD-10PAU-B*1 094050

ZX-1.2YN-80 ZX-1.2YN-24 093409 LD-40PSU*2 094048

*1. The 24 V DC power supply and external volume are required separately.

*2. A constant voltage control method is used. Notes

For substitution models, the powder brake and manual power supply need to be replaced in pairs.

[Issue No.] ZD-5013A

[Title] Production Discontinuation of the 80 V DC powder brake/manual power supply [Date of Issue] July 2017

(2)

TECHNICAL BULLETIN

[

2/2

]

[Issue No.] ZD-5013A

Revised History

Revision Date Description

A July 2017 First Edition

参照

今ダウンロードする ( PDF - 2 ページ - 89.32 KB )

関連したドキュメント

Introduction In this paper we will study existence of positive solutions to a system of the form (D

Section 3 is first devoted to the study of a-priori bounds for positive solutions to problem (D) and then to prove our main theorem by using Leray Schauder degree arguments.. To show

In order to solve this problem we in- troduce generalized uniformly continuous solution operators and use them to obtain the unique solution on a certain Colombeau space

In order to solve this problem we in- troduce generalized uniformly continuous solution operators and use them to obtain the unique solution on a certain Colombeau space1. In

UNIVALENCE OF NORMALIZED SOLUTIONS OF

In this section we prove the lemmas used to obtain Theorem A and The Main Theorem in section 4.. Since all of the results of this section are stated for W(,z)

The Analysis of the Artifacts due to

While conducting an experiment regarding fetal move- ments as a result of Pulsed Wave Doppler (PWD) ultrasound, [8] we encountered the severe artifacts in the acquired image2.

0 is the upper limit of the time interval on which we want to study the time evolution of ψ (here, ˙ψ is the derivative ofψ with respect to the time variablet)

In the proofs of these assertions, we write down rather explicit expressions for the bounds in order to have some qualitative idea how to achieve a good numerical control of the

The algorithm appears to run in average time that is softly quadratic and we prove that this is the case for almost all of the steps

But in fact we can very quickly bound the axial elbows by the simple center-line method and so, in the vanilla algorithm, we will work only with upper bounds on the axial elbows..

Visualizing Production Surfaces in 3D Diagrams

In this contribution, we present algorithms which can be used to determine and visualize a production frontier in the form of an efficient hull in a 3D diagram in the case where

in this Annex), each of the nonoriginating materials used in the production of the good shall be required to undergo the applicable CTC

- Parts of the foregoing machinery, apparatus or equipment Plates, cylinders and other printing components; plates, cylinders and lithographic stones, prepared for printing purposes